Amana Oven Parts

Light Bulb - 40W

11 Reviews

Part Number: 8009

This 40-watt light bulb has a standard screw-in base. It is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Long Oven Sensor

4 Reviews

Part Number: 12001656

The oven sensor detects the temperature within the oven cavity and sends the information to the control board. If your oven is not heating evenly, has little or no heat when baking, or is too hot, you may need to replace the sensor. This long oven sensor kit comes with two harness adapters and is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Door Hinge

5 Reviews

Part Number: WP74008014

The door hinge attaches to the side of the door allowing the oven door to open, close, and stay open at an angle. If your door is not opening and closing correctly you may need to replace the hinge. It is recommended to replace both hinges at the same time. The hinge measures 20 1/2-inch and is made of metal. This is a genuine OEM part.

Touch-Up Paint - White

5 Reviews

Part Number: 72017

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Thermostat/Selector Knob

1 Review

Part Number: WP4168403

The thermostat knob is a little over one inch in diameter. It is a chrome knob and will accept a D shaped shaft. This part lets you control the amount of heat coming from the oven. The knob is genuine OEM part, made entirely of plastic, and is sold individually.

Thermal Fuse

8 Reviews

Part Number: WPW10545255

This thermal fuse is a manufacturer-approved replacement part for your oven. In the event of a power surge or overheating, the thermal fuse will protect the controls from damage. Replacing the blown fuse is an easy repair and involves removing the top of the oven to swap out the fuse. Make sure to disconnect the power source to the oven before beginning this repair.

Spray Paint - 12 oz. - White

1 Review

Part Number: 350930

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.

GASKET-OVN

1 Review

Part Number: W11623080

Fully Open Bake Element (15-1/4" long x 15.5" wide)

Part Number: WP77001092

This bake element is a fully open fixed style and is used for electric ranges and ovens. The element is located inside on the bottom of the oven cavity. The element carries 240 volts, 2400 watts, it is 15-1/4 inches wide, and 15-1/2 inches long. The depth of the terminals for the bake element is 2-1/2 inches, making a total element length of eighteen inches. If the oven is not heating evenly, element will not heat or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM part. Please remember to disconnect the power to your oven before starting the repair.

Flat Style Oven Igniter

6 Reviews

Part Number: 786324

This part is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter, be very careful not to touch the black element part of the igniter as it is very fragile. You will need to reuse the original bracket when installing the new igniter.