YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken Maytag Dryer ruin your day. Repair your Dryer with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all Maytag Dryer parts to help you repair any of your home appliances.
This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and is recommended to change both at once.
Easy Part #:
In Stock - Ships Today
At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. Also, a rivet tool is required for this kit - purchase locally.
This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
This roller shaft acts as the axel for the drum roller. Also known as drum roller axle.
This part is sold individually.
This screw is sold individually.
This comes with a metallic hub clip to hold it firmly in place.
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color. Sold individually.
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
This part senses the flame for heat allowing the gas valve to open.
At 91-5/8" long, this dryer drum belt has 5 ridges and is 3/8" wide.
This part replaces older two terminal switches.
This wheel spins on the pulley shaft.
This roller shaft hex nut measures well under an inch long. It is made of metal and is sold individually.
This kit comes in two pieces: the catch and the clip.
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
This gray levelling leg foot pad is made of rubber.
This seal can be used for the front or rear drum. Adhesive is NOT included.
This part is used to help the belt to rotate the drum.
Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.
10 - 16 x .375
This filter collects lint as it passes through the dryer vent.
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.
This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.
Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 degrees Fahrenheit. The differential of this thermostat is 20 degrees, meaning that with this thermostat, the heating element will cycle back on once the internal temperature drops by 20 degrees.
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is used for many gas clothes dryers.
This white lint filter is a slide-in style type of screen. This filter collects lint as it passes through the dryer vent.
Please NOTE: You must be able to read the words "Clean Before Loading". If you cannot read the words, then it will not fit your appliance.
Use of this rivet requires a rivet tool.
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".
This foot pad is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. Sold individually.
This ten watt appliance light bulb is used with both washers and dryers. Sold individually.
Seal only, adhesive not included.
A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.
This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.
This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to replace both at the same time.
This high limit/safety thermostat is used to prevent overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 200 degrees Fahrenheit. The element will kick back in when the temperature drops to 170 degrees Fahrenheit. Differential of 30 degrees.