Roper Ice Maker Parts

Ice Maker Water Fill Tube Kit

2 Reviews

Part Number: WP2196157

The ice maker fill tube is used to supply water to the ice maker during the fill cycle and is located in the back wall of your refrigerator/freezer. The fill tube is 10-inches long and includes a compression nut and a tube insert. If the fill tube is cracked or leaking water you will need to replace it. This part is white in color, made of plastic, and is a genuine OEM part. Please remember to disconnect the power and shut off the water supply before starting your repair.

Icemaker Control Assembly

6 Reviews

Part Number: W10190935

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. It also controls the heater, the water inlet valve, the cube size, and cube ejection. The control assembly is located under the white cover of the ice maker. If the ice maker is making too much ice or not making ice at all, you may need to replace the control assembly. The motor is not sold separately. This is a genuine OEM part. Please make sure you disconnect power to the refrigerator before starting your repair.

Refrigerator Single Water Inlet Valve

4 Reviews

Part Number: WP2315576

The single water inlet valve is used to supply water to the water dispenser and the ice maker. The valve is 60Hz 120 Volts and 35 watts. If your ice maker isn’t producing ice or the water dispenser not dispensing water, the solenoid might have gone bad and will need to be replaced. This valve includes 1/4” tubing and a plastic union. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the refrigerator before starting the repair.

Water Tube Kit

1 Review

Part Number: W10823511

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Water Inlet Hose Washer

Part Number: WP16123

The washer is black in color and works in conjunction with the fill hose in your washer. This washer helps by creating a watertight seal to avoid leaking. Over time the washer may be worn down or damaged which will allow water to pass through and start leaking and will need to be replaced. This part measures 1-1/16” x 5/8” and is made of rubber. This is a genuine OEM part and is sold individually.

Cycling thermostat

Part Number: WP627985

The ice maker thermostat, also known as bi-metal device, regulates and controls the activation of the icemaker ejection cycle. The thermostat lets the ice maker know when it is cold enough to produce ice. If your ice maker is not making ice or not dispensing ice, you may need to replace the thermostat. This is a genuine OEM part and comes with two retaining clips. Please remember to disconnect power to your refrigerator before starting your repair.

Water Fill Cup and Bearing

1 Review

Part Number: WP628356

The ice maker fill cup and bearing dispenses the water into the ice mold during the fill cycle. If your ice maker is not making ice, is leaking, or the cup or bearing is cracked, you will need to replace this part. This part is three inches long, white in color, and is made of plastic. It is a genuine OEM part. Please remember to disconnect the power and water supply to your refrigerator before starting the repair.

Ice Mold

1 Review

Part Number: WPW10190929

This ice cube mold and heater assembly has a flake resistant surface with separations that mold eight ice crescents and is used with modular style icemakers on some refrigerators. The mold heater is an electrical device that thaws the ice quickly, so it can be released from the icemaker mold. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair.

Compression Nut

1 Review

Part Number: WP627018

This single 1/4-inch compression nut is used to connect the lines that supply water to the correct components, the water dispenser and the ice maker, with the plastic water line of the icemaker assembly. This is a genuine OEM part. Please remember to disconnect the power and water supply to the refrigerator before starting your repair.

Shut Off Arm

Part Number: WP627792

The shut off arm works in conjunction with the ice maker in your refrigerator. When the shut off arm is high enough the ice maker will shut off and no more ice will be produced until the level of ice in the bin drops. The ice maker can be turned off by lifting the arm all the way to the top until in a locked position. This part is made of metal, and measures approximately 9 inches wide and 4 inches in height.