Jenn-Air Washer Parts

Belt Kit

6 Reviews

Part Number: 12112425

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Spray Paint - 12 oz. - White

1 Review

Part Number: 350930

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.

Drive Belt - 51 inches long

2 Reviews

Part Number: WP21352320

This V-style drive belt is about 51-inch long and 3/8-inch wide. This part is made to slip onto the motor pulley to bring the basket up to the speed required. The belt encounters wear and tear over time. If your washer will not drain, spin, or agitate, you may need to replace your belt. It is recommended to disconnect the power to your washer before you start your repair. This V-style belt is a genuine OEM part.

Hose Clamp

Part Number: WP596669

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Lid Hinge

Part Number: WP35-2044

The lid hinge attaches to the lid of your washer to allow the lid to pivot open and closed when in use. This part is the female end of the lid hinge. The lid hinge is an inch and a half long. It is all white in color and is made entirely of plastic.

Lid Hinge Pin

Part Number: WP35-2045

The lid hinge pin allows the lid to pivot open and closed correctly. This part is the male end of the lid hinge. If the lid is not opening or closing properly you may need to replace the lid hinge pin on your washer. This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic.

Screen

1 Review

Part Number: WP96160

Found on the water inlet valve.

High Temperature Adhesive - 2oz.

1 Review

Part Number: WPY055980

This is replacement high temperature adhesive for your washer and dryer. It is designed to hold objects together, and will not disintegrate at a high temperature. This is a 2-ounce tube of adhesive that is sold individually. This is an OEM product sourced directly from the manufacturer.

Tub Bolt

Part Number: W10175939

This is an outer tub bolt and gasket.

Transmission Pulley and Bearing Kit

Part Number: 12002213

The transmission pulley and bearing kit, also known as a thrust bearing kit, is located on the drive shaft. If your washer won’t agitate during use, drum won’t drain, or there is a loud noise during operation, you may need to replace this part. A worn bearing also causes slow spinning or no spin at all. This kit includes the pulley that rotates to spin the tub, washer, and thrust bearing that fits between the pulley and the transmission shaft, 2 upper race washers, 1 lower race washer and the instruction sheet. This is a genuine OEM kit; the parts are not available separately. Please remember to disconnect the power and water supply to the washer before starting the repair.