White-Westinghouse Washer Parts

Door Strike

13 Reviews

Part Number: 131763310

This is a door strike for your washing machine. It is the piece that activates the door switch once the door is closed. If your washer will not start, will not fill with water, or the door will not open/close you may need to replace the door strike. This part is white in color, made from plastic, and measures approximately 2 1/2 inches. This is a genuine OEM part.

Dispenser Inlet Gasket

Part Number: 134371300

The water inlet valve gasket helps prevent water from leaking between the water inlet valve and the dispenser drawer housing. If your washer is leaking or filling slowing, the gasket could be worn or damaged and will need to be replaced. The gasket is black in color, made of rubber and measures approximately 3/4” of an inch high. Please remember to disconnect the power and water supply before starting the repair. This is a genuine OEM part.

Shock Absorber Kit

3 Reviews

Part Number: 5304485917

The shock absorber kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin, and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during its cycles. If one or both of them break or wear out it will cause the washer to vibrate or shake and will need to be replaced. This kit is a genuine OEM part. Please remember to disconnect the power to your appliance before starting the repair.

Drain Pump - 120V 60 Hz.

2 Reviews

Part Number: 137221600

The drain pump is what your washer uses to remove the water from the tub. The pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or has a burning smell, you may need to replace the drain pump. This pump has 120 volts, 60 hz and is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

Front Load Washer Door Lock and Switch Assembly

8 Reviews

Part Number: 131763256

Single Shock Mounting Pin

Part Number: 131268300

The shock absorber mounting pin, also known as a locking pin, is used to hold the shock absorber in place. If your washer is shaking, moving, or making noises you may need to replace the pin. This part is white in color, made of plastic, measures 3 inches long, and is sold individually. Check your model to see how many are required for your model. Please remember to disconnect the power and water to the washer before starting the repair.

Agitator

Part Number: 3204401

The agitator is used in top-loading washing machines to help move the clothes around by rotating back and forth through the detergent and water to wash them. If your agitator won’t agitate or is damaged it will need to be replaced. The agitator is approximately 19” tall with a base diameter of about 13”, white in color and made of plastic. The hub has been changed from a hex to a spline. The agitator drive block and cap must be ordered separately. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.

Drive V-Belt

2 Reviews

Part Number: 134511600

This drive belt is designed to ride on the pulley until the basket gets up to speed. If your washer drum will not agitate or spin, you may need to replace your belt. It is recommended to disconnect the power to your washer and shut off the water supply before you start your repair. This drive belt is a genuine OEM part.

Bellow Kit

1 Review

Part Number: 134515300

Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle. NOTE: This part has been redesigned by the manufacturer and is interchangeable with the old design.

Drain Pump - 60Hz 120V

1 Review

Part Number: 137108000

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.