KitchenAid Dryer KGYS750GQ1
Repairing your KGYS750GQ1 KitchenAid Dryer is simple with official replacement parts made to fit your model. View a selection of popular parts, or review parts lists for each of the
KGYS750GQ1 model diagrams below. Trust us to help you find the part you need and get your
KGYS750GQ1 KitchenAid Dryer running again.
Diagrams for KitchenAid KGYS750GQ1 Dryer
There are 4 diagrams for KGYS750GQ1. Click on the diagram where you think your part is located.
Most Popular KGYS750GQ1 Parts
These are the most commonly purchased repair parts for KGYS750GQ1.
-
![Multi Rib Belt - 92-1/4" – Part Number: 341241](https://easyappliancepartscom-evbpg7caa2aehnhz.z01.azurefd.net/assets/partimages/346995_1_M.jpg "Multi Rib Belt - 92-1/4" – Part Number: 341241")
(42)
This dryer drum belt has four ridges, three grooves, 1/4-inch wide and 92 1/4-inch long. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.
-
(2)
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the drum roller only and does not include the tri-rings. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.
-
(12)
This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.
-
(22)
This 3-wire with leads dryer door switch is an on and off mechanism that prevents the dryer from operating while the door is open. The dryer will not operate until the door switch signals that the dryer door is closed. If the dryer won’t start, the lever broke off, or the switch shorted out, the appliance will not operate and the part will need to be replaced. This switch is a genuine OEM part and replaces the 2-wire switch. Please remember to disconnect the power to the dryer before starting the repair.
-
(4)
The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.
-
(9)
This drive motor operates the dryer by turning the drive belt which spins the drum and will fit most Whirlpool incorporated dryer brands before 1996. If the motor has shorted out, it will no longer turn the drum and will need to be replaced. The drive motor includes the pulley that is not available separately. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.