Dryer Elements and Burners

Heating Element - 240V 5400W

21 Reviews

Part Number: 279838

This 240V/5400W heating element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current, causing the wire to heat up. The heat produced is used to dry the clothes in your dryer. If the dryer has no heat, takes too long to dry, or the heating element burns out, the heating element will need to be replaced since it cannot be repaired. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Dryer Heating Element

10 Reviews

Part Number: WP3387747

When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.

Dryer Heater Element

6 Reviews

Part Number: WP8544771

Heating Element Assembly

5 Reviews

Part Number: 131553900

This E-line assembly comes with a felt strip and insulators already attached. Heating elements are strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer. If your dryer has little or no heat you may need to replace the heating element. This is a genuine OEM part. Please remember to shut off the power to the dryer before starting the repair.

Heating Element - 5300W

1 Review

Part Number: DC47-00019A

Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.

Surface Burner - 8 Inch - 2600W

Part Number: WP660533

This 8” plug in style surface burner element provides heat to the cooking surface of your range. The burner element has looped terminal ends, 2600 watts, and a 5-turn. If the burner element is not heating it could be the element or the burner switch. You can use a multimeter to test the element or the switch for continuity. This is a genuine OEM part; the manufacturer recommends replacing the burner receptacle when you replace the surface burner element. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. This part is sold individually.

Heating Element Connection Wire Kit

1 Review

Part Number: 279457

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Standard Y-Frame Range Surface Burner

3 Reviews

Part Number: WP660532

This standard Y-frame 6” surface element is a genuine OEM part that supplies heat to the cooking surface on your range. It has four turns, a black center medallion, looped terminal ends and carries 15000 tts. If your element is not heating, you may need to replace it. Please be sure to disconnect the power to your range before starting your repair. The manufacturer suggests replacing the receptacle at the same time.

Heating Element

6 Reviews

Part Number: WP4391960

The drum glide helps the front drum rotate smoothly and quietly while operating. If your dryer won’t tumble or is noisy, the glide could be worn down, causing a metal on metal noise. In this case it will need to be replaced. It is recommended to replace both glides at the same time and two is required for the dryer. The drum glide is a genuine OEM part and is sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Dryer Heater Element

3 Reviews

Part Number: 134792700

This 3-coil 5500 watts heating element with housing is used to produce heat to dry the clothes in your dryer. The heating element is strung with a coiled wired. The wire receives, but resists a controlled electric current causing the wire to heat up to dry your clothes. If there is no heat or it is taking too long to dry, you may need to replace the heating element. Check for a blown thermal fuse or thermal cut off. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.