GE Dryer Parts

Drum Bearing Slide - White

(3)

Part Number: WE1M504

This single white drum bearing slide attaches to the outer-most sides of the bearing to help support the front of the drum as it rotates. If your dryer is making loud noises or the drum will not tumble, you many need to replace the slides. The manufacturer recommends replacing both slides at the same time; there are 2 slides per dryer. This is a genuine OEM part. Please make sure to disconnect power to the dryer before starting your repair.

Drive Belt

(8)

Part Number: WE12M29

This drive belt is about 89 1/2-inch long and has 4 ribs. This part is made to wrap around the drum, to rotate it. If your dryer drum will not turn, then you may need to replace your belt. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.

Drum Bearing Slide - Green

(1)

Part Number: WE1M1067

This single green drum bearing slide attaches to the outer-most sides of the bearing to help support the front of the drum as it rotates. If your dryer is making loud noises or the drum won?t tumble you many need to replace the slides. The manufacturer recommends replacing both slides at the same time. There are 2 slides per dryer. This is a genuine OEM part. Please make sure to disconnect the power to the dryer before starting your repair.

Lint Filter (White Frame)

(6)

Part Number: WE18X25100

The lint filter is used to collect lint and debris as it passes through the dryer vent. It is recommended to clean the lint filter before every load. If your dryer takes too long to dry, the lint filter frame becomes damaged or the filter has torn you may need to replace the lint filter. The frame is white in color. This is a genuine OEM part.

Rear Drum Bearing Kit

(1)

Part Number: WE25M40

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Over time the drum bearing will wear out, once it has the dryer may make some noise and the drum bearing will need to be replaced. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

D-Shaped Knob Insert Clip

Part Number: WE1X980

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Front Drum Bearing

(9)

Part Number: WE3M26

The drum support bearing helps your dryer operate as quietly as possible by allowing the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. If your dryer is noisy or making a squeaking sound, the slides are probably worn and both slides will need to be replaced. This part measures 10-inches in height and 19 1/2-inches inside width. Four drum glides are used with the drum support bearing and are sold separately. The support bearing is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Door Switch

(2)

Part Number: WE4M415

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

Interlock Switch

Part Number: WD21X10261

This switch is multi purpose, for a dishwasher the switch is a simple on/off mechanism that prohibits the appliance from operating when the door is open. For a dryer, this switch will let the dryer know if the belt breaks and shut power off to the dryer. If your dryer will not operate or your dishwasher will not start you may need to replace the switch. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Door Strike

(1)

Part Number: WE1X1192

The door strike for your dryer is mounted on the dryer door. It fits into the door latch and keeps the door closed. If the door strike is damaged or missing, the door will not lock properly and not only will this cause the door to swing open, but it won’t allow the dryer to start properly. It is a small piece of metal, about 1 inch in length and is sold individually.