General Electric Refrigerator Filters

Refrigerator Water Filter

4 Reviews

Part Number: RPWFE

This NSF-certified water filter helps to improve the taste, quality, and health of your water by removing a number of contaminants including mercury, lead, and trace pharmaceuticals. The filter should be replaced every six month or after 300 gallons of water have been filtered. If you are unsure if your filter is due for replacement, another indicator is if the water flow from the dispenser has slowed down considerably. Replacing this part is a simple task that does not require any tools or shutting off the water or power supply to your fridge. Once the new filter has been installed, be sure to run at least two gallons of water through before consuming.

Refrigerator Ice and Water Filter

5 Reviews

Part Number: MWFP

Refrigerator Water Filter

Part Number: XWFE

This water filter is found in the rear upper-right corner of the interior of the refrigerator. If your model has a replacement indicator light it will turn red to signal the need for a replacement. If your model does not have an indicator light, the filter cartridge should be replaced every six months or earlier if you notice a decrease in the flow of water from the dispenser. The filter media is carbon black and reduces leads, some pharmaceuticals, and fifty other contaminates. It is 2 inches deep, 6 inches high, 2.25 inches wide and weighs approximately 1 lbs. When it comes time to replace the filter, first discard the old one by turning it to the left to remove. It will release itself when it has been turned far enough. Installation instructions are quick and simple but can vary slightly depending on if it is a bottom-freezer, side-by-side or multi-door bottom-freezer model. Refer to the user instructions for you filter. Do not forget to reset the filter change indicator if applicable. In bottom-freezer and side-by-side models this is done by pressing and holding the RESET WATER FILTER bottom for three seconds. On a multi-door bottom-freezer model, press the button underneath the Confirm Filter Change message while the water is dispensing. On select models this reset is done automatically once a new filter is installed.

Refrigerator Water Filter

1 Review

Part Number: GSWF

This OEM filter is sold individually. Change your filter every 6 months for the best results. This filter is found in top-freezer and bottom-freezer refrigerators located in the back upper right corner. It measures 4.75-Inches deep, 9.5-Inches high, and 5.25-Inches wide. It is certified to reduce particles, chlorine-resistant cysts, lead and five other impurities. The pressure requirement is 40-120 PSI (if yours exceeds this, you?ll need to install a pressure-timing valve), and the operating temperature needs to be 33-100 degrees Fahrenheit. It filters down to 0.5-1 microns. The installation is simple and does not require any tools or mess. To remove the old cartridge, turn it to the left and pull down carefully. Some water might drip, so keep a cloth handy. To install the new filter, place it into the cartridge holder and turn to the right until it will no longer turn. If you have a top-freezer model it should be situated vertically, and if it is a bottom-freezer model, it should be placed horizontally. Be careful not to over-tighten. If your model has a replacement indicator light, reset it by pushing and holding it down for three seconds. If your model has a dispenser, run water through it for approximately 3 minutes to clear the system. Please note that this filter will not work in Kenmore brand models.

Water Filter

Part Number: MSWF

This OEM water filter works with side-by-side and bottom freezer refrigerators. You will find this filter mounted in a vertical position in the back upper right-hand corner of the refrigerator compartment. If your model does not have an indicator light, remember to use the month and year stickers on the new cartridge to remind yourself to replace it in another 6 months. Replacement timelines can vary according to your local water conditions. To install the new filter, you will first match the threads with the corresponding threads on the holder. Position the top of the new cartridge up into the holder without pushing it upward. Carefully turn it to the right until it will no longer turn. Make sure you run water through the dispenser right after installation. This clears the system and prevents sputtering. If you have an LCD model, press the Filter Replaced button to reset. If you have a non-LCD model, press and hold the Reset Water Filter button on the dispenser for a few seconds. This filter filters down to 0.5-1 microns. The lower the micron the more toxins are caught and lessened.

FILTER HEAD Assembly AND TUBE

Part Number: WR17X11894

Odor Filter Cartridge

Part Number: ODORFILTER

The odor filter helps remove food odors, preventing them from circulating and affecting other foods within the fresh food compartment.

In-Line Water Filter

Part Number: GXRTDR

This OEM filter measures 2.1-Inches by 2.2-inches by 12.7-Inches. It is used to reduce bad tasting water, while also lessening dirt, rust, and other sediments. It is recommended to replace this filter every six months or 2500 gallons. If performance of the filter has changed, it may need to be replaced sooner, depending on the water conditions. It is sold individually. This filter is compatible with refrigerators that do not have built-in filtration. It is used in side-by-side and top-freezer refrigerators. The filter has a new design with quick connect fittings at the end of the filter so it can be easily installed behind your refrigerator. This filter only works with plastic lines. The only tool you may need for this repair is something to cut your tubing with. To install, first turn off the water supply. The filter can now be inserted into the 1/4-Inch OD supply tube that carries water to the appliance. Now cut the tubing in a straight line (if installing for the first time, if this is a replacement you can skip this step). Push the tubing into the filter inlet until it is flush with the fitting collar. Place the filter outlet over a bucket and flush it out by turning on the water supply valve and allowing it to flow for about five minutes. Now connect the outlet of the filter to the water line going to the appliance. Turn on the water supply.

SmartWater - Water Filter Canister

Part Number: MXRC

Bring clean, fresh tasting water to your home with the MXRC water filter. Reduces chlorine taste and odor Fits in GE Monogram refrigerator models starting with: ZIS36, ZIS42, ZIS48, ZISB36, ZISB42, ZISB48, ZISS36, ZISS42, ZISS48, ZISW36, ZISW42, ZISW48 This water filter is easy to install, and no tools are required. Filter lasts 6 months or 300 gallons. GE MXRC Specifications: Round metal canister with white and grey label 1 filter per pack 6 inches long, 4 inches in diameter

Water Filter Adapter

1 Review

Part Number: ADAPTER

This is a replacement water filter adapter for your refrigerator. It is approximately 2.5 inches in diameter and is made of plastic. The filter adapter allows you to connect your water filter to your refrigerator. If the adapter is broken, your ice maker may not dispense ice, and your refrigerator may not dispense water. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.