Hotpoint Dryer Parts

Drive Belt

13 Reviews

Part Number: WE03X29897

This drive belt is about 89 1/2-inch long and has 4 ribs. This part is made to wrap around the drum, to rotate it. If your dryer drum will not turn, then you may need to replace your belt. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.

Drum Bearing Slide - White (Sold individually)

4 Reviews

Part Number: WE1M504

This single white drum bearing slide attaches to the outer-most sides of the bearing to help support the front of the drum as it rotates. If your dryer is making loud noises or the drum will not tumble, you many need to replace the slides. The manufacturer recommends replacing both slides at the same time; there are 2 slides per dryer. This is a genuine OEM part. Please make sure to disconnect power to the dryer before starting your repair.

Lint Filter

11 Reviews

Part Number: WE03X23881

This is a genuine OEM part that works for some models of GE, and Hotpoint models. This Lint Filter is used for Dryer.

Drum Bearing Slide - Green (Sold individually)

1 Review

Part Number: WE1M1067

This single green drum bearing slide attaches to the outer-most sides of the bearing to help support the front of the drum as it rotates. If your dryer is making loud noises or the drum won?t tumble you many need to replace the slides. The manufacturer recommends replacing both slides at the same time. There are 2 slides per dryer. This is a genuine OEM part. Please make sure to disconnect the power to the dryer before starting your repair.

Timer Knob

13 Reviews

Part Number: WE1M652

This timer knob for a dryer is an authentic replacement part and accepts a D-shaped shaft. The knob is white in color and measures 3 inches in diameter. The timer knob attaches onto the shaft of the timer and allows you to select the amount of time your dryer will run. If your dryer timer will not advance or your dryer will not start you may need to replace the timer knob.

Front Drum Bearing

10 Reviews

Part Number: WE3M26

The drum support bearing helps your dryer operate as quietly as possible by allowing the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. If your dryer is noisy or making a squeaking sound, the slides are probably worn and both slides will need to be replaced. This part measures 10-inches in height and 19 1/2-inches inside width. Four drum glides are used with the drum support bearing and are sold separately. The support bearing is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

DRYER BEARING SLIDE 2PK

Part Number: WE03X37319

This drum glide bearing is an authentic OEM replacement part that is compatible with dryers. It is white in color and made of highly durable plastic. The bearing allows the drum to rotate smoothly and dry your clothes thoroughly and evenly. It keeps the drum stable and protects it from excessive friction damage. Over time, the bearing may wear down or break due to normal aging or wear from repeated use. If the bearing is no longer able to support the drum, you will likely notice unusually loud grinding or squeaking noises from the dryer. You may also notice increased drying times due to poor drum rotation. Inspect all the bearings on your dryer, as they tend to wear down at the same time. Each drum glide bearing is sold individually.

DRYER BEARING SLIDE 2-PACK

Part Number: WE03X37320

This OEM replacement dryer slide bearing is white in color, and approximately 3 inches long. The slide bearings are supportive linings for your dryer. If they have eroded, or are damaged, the drums will scrape against metal during the drying cycle which will produce a squealing, or scraping sound.

Duct Felt Seal

Part Number: WE09X27634

The duct felt seal allows the front of the drum to glide smoothly on the exterior panel while the drum is rotating. The seal is located between the back of the drum and the rear dryer panel. If the heat is escaping from the drum area causing the dryer to run too long or if there are marks on your clothes you many need to replace the duct felt seal. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Push-to-Start Switch

3 Reviews

Part Number: WE4M416

This switch is used to activate the dryer.