10650228010 Kenmore Refrigerator Parts List

Water tube kit (water tube)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Arm-shut

Door shelf (trim)

This authentic Whirlpool refrigerator part is a door shelf rail. It snaps into your refrigerator door and prevents items from sliding or falling out when your open the door. It is made of plastic and is approximately 17 inches in length by 5 inches in width. To replace this part, simply snap out the old door shelf rail and install the new one.

Spray paint - 12 oz. - white (spray)

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.

Floating baffle (baffle)

This ice auger support, also known as a baffle, is a manufacturer-approved replacement part for your refrigerator ice maker. This part can become cracked or damaged, preventing your ice auger from doing its job. This repair requires extensive disassembly; take photos as you go to make reassembly easier. To replace this part, life the ice door out of the way and life the ice arm into the off position. Pull out the ice bucket and use a 1/4 inch nut driver to remove the screws holding the ice container and connecting rod in place. Pry the e-clip and washer off the bottom of the auger assembly. Use a 9/16ths wrench to remove the nut at the bottom of the auger. Pull off the auger teeth assembly and replace the auger support with your new part. Now you can begin reassembling.

Screw

This screw is sold individually.

Cycling thermostat (thermostat)

The ice maker thermostat, also known as bi-metal device, regulates and controls the activation of the icemaker ejection cycle. The thermostat lets the ice maker know when it is cold enough to produce ice. If your ice maker is not making ice or not dispensing ice, you may need to replace the thermostat. This is a genuine OEM part and comes with two retaining clips. Please remember to disconnect power to your refrigerator before starting your repair.

Door light switch (light switch)

The white door light switch is in the control panel section of your refrigerator. The light will turn on when you open the door. If the light doesn?t turn on when the door is open the contacts in the switch could be burnt out and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting your repair.

Screw

Sold individually.

Levers retainer/clip (clip)

This part is the replacement dispenser lever retainer for your refrigerator. It is made of metal and is approximately 2 inches long and ½ an inch wide. The bottom half of the dispenser lever retainer holds in the pivot points of the ice and water arms. If it breaks, the arms will be loose and can shake around. The top half springs the ice and water arms back into the original position, and if the retainer is broken, they will not be able to do this. The dispenser lever retainer is found behind the dispenser trim and can be removed with a ¼ inch nut driver. This part is sold individually and is an OEM part.

Thimble top (thimble)

For white, biscuit, black and stainless models.

Light socket kit (light socket)

The bulb is sold separately.

Fan blade

The fan blade is used to blow air over the condenser.

Installation screw (screw)

This screw is sold individually.

Screw

Sold individually.