10650532102 Kenmore Refrigerator Parts List

Ice dispenser door chute (door, ice)

*Please note, this door chute is no longer being manufactured with a heater.

Evaporator fan blade (fan blade)

If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate the cold air into the refrigerator and freezer sections. The fan blade is white in color and made from plastic. This is a genuine OEM part. Please be sure to disconnect the power to your refrigerator before starting your repair.

Refrigerator shelf end cap - white (end cap (2))

Sold individually.

Water tube kit (tube, water)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Arm-shut (shut off arm)

Spray paint - 12 oz. - white (enamel, white (12 oz. Spray can) (caution: The spray paint is not to be used where the paint may make contact with the door gaskets.))

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.

Floating baffle

This ice auger support, also known as a baffle, is a manufacturer-approved replacement part for your refrigerator ice maker. This part can become cracked or damaged, preventing your ice auger from doing its job. This repair requires extensive disassembly; take photos as you go to make reassembly easier. To replace this part, life the ice door out of the way and life the ice arm into the off position. Pull out the ice bucket and use a 1/4 inch nut driver to remove the screws holding the ice container and connecting rod in place. Pry the e-clip and washer off the bottom of the auger assembly. Use a 9/16ths wrench to remove the nut at the bottom of the auger. Pull off the auger teeth assembly and replace the auger support with your new part. Now you can begin reassembling.

Screw

This screw is sold individually.

Ice auger kit (auger)

This kit includes the metal auger, auger coupling and washer.

Cycling thermostat (thermostat (also order 542639 cement alumilastic))

The ice maker thermostat, also known as bi-metal device, regulates and controls the activation of the icemaker ejection cycle. The thermostat lets the ice maker know when it is cold enough to produce ice. If your ice maker is not making ice or not dispensing ice, you may need to replace the thermostat. This is a genuine OEM part and comes with two retaining clips. Please remember to disconnect power to your refrigerator before starting your repair.

Door light switch (switch, light)

The white door light switch is in the control panel section of your refrigerator. The light will turn on when you open the door. If the light doesn?t turn on when the door is open the contacts in the switch could be burnt out and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting your repair.

Fresh food door gasket (door gasket, magnetic)

This door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.

Ice container and auger assembly (ice container assembly)

This part may come with a plastic or metal auger depending on the factory. It will work with your appliance if found with the model number. (Make sure you install properly at back of ice container, because it must be engaged for the crushed ice feature to work)

Shelf support (stud assembly (also on crisper cover, as shown, if applicable))

Sold individually.

Single shelf stud (stud assembly (if applicable))

This part screws into the side of the wall in your fresh food compartment and supports a shelf.