10670939900 Kenmore Refrigerator Parts List

Replacement ice maker (icemaker)

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Refrigerator single water inlet valve (inlet valve)

The single water inlet valve is used to supply water to the water dispenser and the ice maker. The valve is 60Hz 120 Volts and 35 watts. If your ice maker isn’t producing ice or the water dispenser not dispensing water, the solenoid might have gone bad and will need to be replaced. This valve includes 1/4” tubing and a plastic union. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the refrigerator before starting the repair.

Door shelf retainer bar end cap (endcap handle)

The door shelf retainer bar end cap connects to the retainer bar on your refrigerator’s door shelf, and attaches it to the refrigerator door. If your shelf retainer bar has become disconnected, a damaged end cap could be the cause. To remove the end cap, first unhook the release tab on both ends of the retainer bar. Slide out the bar and the end caps, and slide out the defective cap. Now, simply replace the end cap and snap the bar with end caps back in place on the refrigerator door. This part is made of white plastic and is sold individually.

Ice maker water fill tube kit (fitting)

The ice maker fill tube is used to supply water to the ice maker during the fill cycle and is located in the back wall of your refrigerator/freezer. The fill tube is 10-inches long and includes a compression nut and a tube insert. If the fill tube is cracked or leaking water you will need to replace it. This part is white in color, made of plastic, and is a genuine OEM part. Please remember to disconnect the power and shut off the water supply before starting your repair.

Bi-metal defrost thermostat (bimetl-def)

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

Refrigerator door switch (light switch)

Door switch turns the light off when you close the door.

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Evaporator fan motor (motor evaporator)

This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.

Crisper pan (pan crisper)

This crisper pan, or drawer, is made for your refrigerator. The drawer has a controlled environment to ensure a proper humidity level to keep your produce fresh for longer. It is clear in color and made of plastic. It is approximately 13 inches by 10 inches at the base of the pan.

Screw

Sold individually.

Ice mold

This ice cube mold and heater assembly has a flake resistant surface with separations that mold eight ice crescents and is used with modular style icemakers on some refrigerators. The mold heater is an electrical device that thaws the ice quickly, so it can be released from the icemaker mold. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair.

Screw

Metallic screw that is less than an inch long. Does not include the plastic washer.

Icemaker motor kit (motor mold)

This kit includes the module motor, ejector arm, and ice stripper arm. The complete icemaker is sold separately.

Water tube kit (water tube)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Refrigerator door shelf rail (door trim)