1067502120 Kenmore Refrigerator Parts List

Replacement ice maker (mold & heater assembly inc 43)

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Single outlet water valve kit (valve, dole)

When energized, the water inlet valve will release water from the supply line into the ice mold and the water dispenser in the refrigerator. If the ice maker is not making/dispensing ice, not dispensing water, or leaking, you may need to replace the water inlet valve. The water inlet valve is in the back section of your refrigerator and will need to be pulled out from the wall. Make sure to disconnect both the water and power supply before starting your repair. The manufacturer has redesigned the valve; it may appear different than the original. The updated valve has a new quick connection. To install the updated valve, cut the retaining nut off the existing water line and gently push into the new valve. This is a genuine OEM part. Please remember to disconnect the power and the water supply before starting your repair.

Water tube kit (tube, valve)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Screen (strainer)

Found on the water inlet valve.

Compression nut (sleeve nut)

This single 1/4-inch compression nut is used to connect the lines that supply water to the correct components, the water dispenser and the ice maker, with the plastic water line of the icemaker assembly. This is a genuine OEM part. Please remember to disconnect the power and water supply to the refrigerator before starting your repair.

Water inlet hose washer (washer)

The washer is black in color and works in conjunction with the fill hose in your washer. This washer helps by creating a watertight seal to avoid leaking. Over time the washer may be worn down or damaged which will allow water to pass through and start leaking and will need to be replaced. This part measures 1-1/16” x 5/8” and is made of rubber. This is a genuine OEM part and is sold individually.

Plastic tubing inserts - 4 included (insert, plastic tube)

These inserts are used with 1/4 inch plastic tubing.

Ice pan (pan, ice inc 70)

Water hose clamp (clamp)

These tube clamps are sold individually. The screw is not included.

Screw

This screw is sold individually.

Transformer screw (screw, 8-18 x 1/2)

This screw is sold individually.

Spacer (spacer, holding switch)

Ice maker drive gear (gear)

The drive gear works in conjunction with the ejector blades in your ice maker. The drive gear attaches to the cam to help rotate the ejector arm to push the ice from the ice maker into the ice container. If the ice maker isn’t dispensing ice you may need to replace this part. The drive gear is approximately 1 1/2” in diameter, white in color and made of plastic. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.

Filter drier tube (drier)

The filter drier tube with system access port, works in conjunction with your refrigerator by filtering the refrigerant that travels through the seal system of your refrigerator. This part measures approximately 10” long and is a genuine OEM part. Please make sure to disconnect the power before starting the repair. Please note it is recommended to have a service technician install the filter drier tube because it involves recharging and recovering refrigerant in the sealed refrigerant system.

Swtch-micr (switch, s.P.D.T.)