Parts for Kenmore Models 1069334201

Icemaker control assembly (module assembly (includes items 37, & 38))

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. It also controls the heater, the water inlet valve, the cube size, and cube ejection. The control assembly is located under the white cover of the ice maker. If the ice maker is making too much ice or not making ice at all, you may need to replace the control assembly. The motor is not sold separately. This is a genuine OEM part. Please make sure you disconnect power to the refrigerator before starting your repair.

Easy Part #:: EAP2341896

Availability:: In Stock

Price:: $85.77

Capacitor (run capacitor)

The run capacitor is attached to the compressor. This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Easy Part #:: EAP11757023

Availability:: In Stock

Price:: $56.39

Refrigerator single water inlet valve (valve solenoid)

The single water inlet valve is used to supply water to the water dispenser and the ice maker. The valve is 60Hz 120 Volts and 35 watts. If your ice maker isn’t producing ice or the water dispenser not dispensing water, the solenoid might have gone bad and will need to be replaced. This valve includes 1/4” tubing and a plastic union. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the refrigerator before starting the repair.

Easy Part #:: EAP11740365

Availability:: In Stock

Price:: $51.99

End cap trim piece (plug-trim)

The end cap trim piece slides into the door trim to help hold the door shelf stay in place. When installing the new end cap trim piece, make sure the two small taps are facing up. This part can be used for the left or right side. The end cap trim piece is white in color, made of plastic and almost 2” long. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11738928

Availability:: In Stock

Price:: $6.45

Ice maker water fill tube kit (fitting, water tube)

The ice maker fill tube is used to supply water to the ice maker during the fill cycle and is located in the back wall of your refrigerator/freezer. The fill tube is 10-inches long and includes a compression nut and a tube insert. If the fill tube is cracked or leaking water you will need to replace it. This part is white in color, made of plastic, and is a genuine OEM part. Please remember to disconnect the power and shut off the water supply before starting your repair.

Easy Part #:: EAP11739222

Availability:: In Stock

Price:: $5.92

Refrigerator door switch (rocker arm switch)

Door switch turns the light off when you close the door.

Easy Part #:: EAP12728638

Availability:: In Stock

Price:: $26.51

End cap trim - white (plug-trim)

This part is the replacement end cap trim for your refrigerator. It is made of white plastic and is approximately 1 inch wide, 1 inch long, and ½ inch thick. This part can also be known as the shelf support retainer as it holds the shelf support in place. If the end cap trim is damaged, the shelf support may not remain in place and you will not be able to store items in your refrigerator door. To replace the end cap trim, carefully disconnect it from both the refrigerator door and the shelf support. Then, snap the new end cap trim into the shelf support and then to the door. This part is sold individually and is an authentic OEM part.

Easy Part #:: EAP11738929

Availability:: In Stock

Price:: $6.47

Fresh food door gasket (door gasket, magnetic)

This white door gasket is used to seal the fridge door when closed.

Easy Part #:: EAP328691

Availability:: In Stock

Price:: $86.30

Water fill cup and bearing (cup, water fill)

The ice maker fill cup and bearing dispenses the water into the ice mold during the fill cycle. If your ice maker is not making ice, is leaking, or the cup or bearing is cracked, you will need to replace this part. This part is three inches long, white in color, and is made of plastic. It is a genuine OEM part. Please remember to disconnect the power and water supply to your refrigerator before starting the repair.

Easy Part #:: EAP11743318

Availability:: In Stock

Price:: $33.67

Ice mold (mold & heater assembly (also order 542638 silicone grease))

This ice cube mold and heater assembly has a flake resistant surface with separations that mold eight ice crescents and is used with modular style icemakers on some refrigerators. The mold heater is an electrical device that thaws the ice quickly, so it can be released from the icemaker mold. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair.

Easy Part #:: EAP11749915

Availability:: On Order

Price:: $121.36

Screw

Metallic screw that is less than an inch long. Does not include the plastic washer.

Easy Part #:: EAP11742721

Availability:: In Stock

Price:: $4.54

Water tube kit (tube water)

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72-inch in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Easy Part #:: EAP11730901

Availability:: In Stock

Price:: $30.10

Crisper pan

Sold individually.

Easy Part #:: EAP11738958

Availability:: In Stock

Price:: $74.13

Cycling thermostat (thermostat (also order 542369 cement alumilastic))

The ice maker thermostat, also known as bi-metal device, regulates and controls the activation of the icemaker ejection cycle. The thermostat lets the ice maker know when it is cold enough to produce ice. If your ice maker is not making ice or not dispensing ice, you may need to replace the thermostat. This is a genuine OEM part and comes with two retaining clips. Please remember to disconnect power to your refrigerator before starting your repair.