Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

1106012990 Kenmore Dryer Parts List

1-15 of 33

Dryer thermal fuse (dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system.)

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Easy Part #:

EAP11741460

Availability:

In Stock - Ships Today

Price:

$16.60

Heating element - 240v 5400w (dryer heating element. If your dryer does not heat first check for a blown thermal fuse on the blower housing before replacing the heating element.)

This 240V/5400W heating element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current, causing the wire to heat up. The heat produced is used to dry the clothes in your dryer. If the dryer has no heat, takes too long to dry, or the heating element burns out, the heating element will need to be replaced since it cannot be repaired. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:

EAP334313

Availability:

In Stock - Ships Today

Price:

$64.64

Thermal cut-off kit (dryer heating element thermal cut-off (thermal fuse) 309 degrees and high limit thermostat 250 degrees, with wiring kit.)

This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. This genuine OEM kit also includes flat heaters with jumper wires. Make sure to disconnect the power source to the dryer before beginning this repair.

Easy Part #:

EAP334299

Availability:

In Stock - Ships Today

Price:

$33.22

Dryer cycling thermostat (dryer cycling thermostat with internal bias heater, l155-25.)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:

EAP11741405

Availability:

In Stock - Ships Today

Price:

$21.58

Rear drum support roller kit (rear drum support roller kit. This kit contains two drum support rollers. If the drum rollers are worn out, the dryer may not turn properly or may be)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:

EAP347627

Availability:

In Stock - Ships Today

Price:

$14.32

Dryer high limit thermostat (dryer high-limit thermostat, l250-80, with terminal extension arm. This thermostat should be closed for continuity at room temperature and opens at ar)

The three-terminal high-limit thermostat with a terminal extension arm acts as a safety mechanism that keeps the dryer from overheating. When the dryer temperature reaches 221 degrees Fahrenheit, the thermostat will shut off power to the heating element until it drops by 80 degrees Fahrenheit. If your dryer has no heat, takes too long to dry or the thermostat has shorted out, you will need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP11742185

Availability:

In Stock - Ships Today

Price:

$16.65

Easy Part #:

EAP334206

Availability:

In Stock - Ships Today

Price:

$8.59

Rear drum felt seal (dryer drum rear felt seal kit with adhesive and instructions.)

This seals Includes adhesive. This part helps seal the drum to prevent hot air from escaping.

Easy Part #:

EAP8691753

Availability:

In Stock - Ships Today

Price:

$49.06

Dryer blower wheel (dryer blower wheel. Used on 29 inch Whirlpool built models with lint filter on top. To remove the blower wheel, unscrew the blower wheel clockwise of)

The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.

Easy Part #:

EAP11743785

Availability:

In Stock - Ships Today

Price:

$25.81

Easy Part #:

EAP11741506

Availability:

In Stock - Ships Today

Price:

$7.07

Two-piece split ring bearing (ring bearing kit, front of dryer drum)

This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during operation, or if there are marks left on your clothes after a cycle, you may need to replace the bearing ring kit. The kit comes with 2 bearings, one for the top and one for the bottom of the dryer drum. Remove the front panel of your dryer to access the dryer drum for this repair. At this point you can use a pair of needle nose pliers to release the old bearing rings from the drum. Snap the new bearing rings on, and reassemble the dryer to complete your repair.

Easy Part #:

EAP334199

Availability:

In Stock - Ships Today

Price:

$46.84

Drum roller shaft - left side (shaft for drum support roller, left side)

Replace the shaft of your left side drum support roller with this part from Whirlpool/Kenmore. This replacement shaft is 2-7/8 inches long. It is meant for use with many of Whirlpool/Kenmore's gas and electric clothes dryers that have been manufactured since 1965. Also known as Drum Roller Shaft.

Easy Part #:

EAP11753706

Availability:

In Stock - Ships Today

Price:

$43.50

Seal (dryer blower housing foam seal with adhesive backing.)

This seal comes with the adhesive backing.

Easy Part #:

EAP12745423

Availability:

In Stock - Ships Today

Price:

$16.44

Drum support roller shaft - right side (shaft for drum support roller, right side)

Replace the shaft of your right side drum support roller with this part. This replacement shaft is 3-3/16 inches long, but does not require a washer or a nut.

Easy Part #:

EAP11753705

Availability:

In Stock - Ships Today

Price:

$48.53

Dryer screw (screw, baffle mounting)

11-16 x 3/4 Sold individually.

Easy Part #:

EAP11748297

Availability:

In Stock - Ships Today

Price:

$5.73

1-15 of 33