1107099699 Parts List

1-15 of 174

M series new style coil kit (valve coil kit)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP334310

Availability:

In Stock

Price:

$13.86

Door catch kit (door latch kit)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:

EAP334230

Availability:

In Stock

Price:

$4.20

Drum support roller (support)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Easy Part #:

EAP11752609

Availability:

In Stock

Price:

$12.22

Lint filter (lint screen)

This filter collects lint as it passes through the dryer vent.

Easy Part #:

EAP1491676

Availability:

In Stock

Price:

$35.62

Idler pulley

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:

EAP334244

Availability:

In Stock

Price:

$19.25

Igniter kit (glow bar igniter)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:

EAP334180

Availability:

In Stock

Price:

$25.58

Drive belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide.

Easy Part #:

EAP11722115

Availability:

In Stock

Price:

$18.30

Leveling foot (leveling feet)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Easy Part #:

EAP1609293

Availability:

In Stock

Price:

$4.53

Thrust washer

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:

EAP11740482

Availability:

In Stock

Price:

$4.58

Tri ring (ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:

EAP11755850

Availability:

In Stock

Price:

$6.48

Thermostat, internal-bias (thermistor)

This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Easy Part #:

EAP11746740

Availability:

In Stock

Price:

$26.40

Radiant Flame sensor (radiant sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:

EAP11741429

Availability:

In Stock

Price:

$26.13

Light bulb - 10w (light bulb)

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Easy Part #:

EAP11739347

Availability:

In Stock

Price:

$10.98

Disposable thermal fuse - two terminal (non-resettable thermal fuse)

This part attaches to the exhaust duct of your clothes dryer.

Easy Part #:

EAP11741444

Availability:

In Stock

Price:

$13.13

Lid switch (lid switch kit)

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Easy Part #:

EAP11723153

Availability:

In Stock

Price:

$22.63

1-15 of 174