110C87562601 Kenmore Dryer Parts List

Dryer thermal fuse (dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system.)

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Door catch kit (dryer door catch kit. This kit includes three different door catches; you will need to select the door catch that fits your model.)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Dryer drum support roller (dryer drum support roller. If the dryer is making a rumbling or knocking noise the rollers may be worn out causing the drum not to turn smoothly.)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Idler pulley (dryer idler pulley. The idler pulley puts tension on the drive belt. If the idler pulley fails to put the proper amount of tension on the belt, the dr)

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Lint filter (dryer lint filter. Air flow is vital to proper dryer operation. The lint filter should be cleaned before every load and replaced if damaged.)

This filter collects lint as it passes through the dryer vent.

Drive belt (dryer drum drive belt, 93 1/2 inches long, 4 ribs 3 grooves.)

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide. This drive belt is 93 1/2 inches long, and 1/4 of an inch wide, with 4 ribs and 3 grooves. To complete this repair, you will need a Phillips screw driver, a 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Make sure to disconnect power to the dryer before beginning this repair.

Thermostat, internal-bias (dryer thermistor. This thermistor should read approximately 11.9k ohms of resistance at 70 degrees fahrenheit (21’ celsius).)

This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Thrust washer (washer. Has a 3/4-inch outside diameter.)

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Dryer repair kit (20ga s/s #4 grain 304,54)

This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings, and one washer. This universal maintenance kit is an all-encompassing kit for fixing a noisy dryer, among other symptoms, but noisy being the most common. It is compatible with 27-inch wide dryers built from 1965 onwards. Be sure to disconnect the dryer or shut off the house circuit breaker for the appliance before you begin your repair. To access these parts, you will need to remove the dryer drum. For this installation you will need a 1/4-inch nut driver, a long flat-blade screwdriver, a short flat-blade screw diver, and a Phillips screwdriver.

Dryer heater element (dryer heating element. If the dryer no longer heats then the heating element may have failed, but it is not the most common cause.)

High limit thermostat and thermal cut-off kit (dryer high limit thermostat and thermal fuse kit. If the dryer does not heat the most common cause is a blown thermal fuse.)

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.

Light bulb - 10w (light bulb, 10 watt.)

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Idler pulley with bracket (dryer idler pulley assembly.)

The idler pulley wheel is now sold with this arm. This idler pulley is for dryers. Idler pulley maintains correct tension on the drive belt to spin the drum.

Moisture sensor (dryer moisture sensor bar. This moisture sensor monitors the clothing’s moisture level and sends a signal to the control board when the clothes are dr)

This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.

Screw, 8/18 x 3/8 (screw, 10-24 3/8)

This screw is sold individually.