Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

11010852991 Kenmore Washer Parts List

1-15 of 167

Agitator directional cogs (agitator dogs)

These agitator directional cogs are commonly referred to as dog ears. They come four in a package and are usually used with direct drive washing machines. When the teeth on the outer edge are worn down the cogs will not engage with the upper agitator, causing it not to agitate properly. It is recommended to replace all four at the same time. These agitator directional cogs are ?-inch high and 1-inchlong and they are a genuine OEM part.

Easy Part #:

EAP388034

Availability:

In Stock

Price:

$4.34

Direct drive motor coupling (coupler)

The newer version of the coupler kit is made with new metal sleeves for added strength. This part is located between the motor and transmission on the direct drive washer that does not have a belt. The coupler will break to protect the motor from damage if the drive motor system seizes up. If your washer will not fill, will not agitate or spin, but it will drain the water from the tub, you may need to replace this part because it has failed. This is a genuine OEM part. Disconnect the power to your washer before starting the repair.

Easy Part #:

EAP1485646

Availability:

In Stock

Price:

$21.18

Direct drive water pump (complete pump)

This pump is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one. This part is used to remove water from the tub during the drain cycle. If your washer is leaking, not draining, pumps but will not spin or fills and drains at the same time you may need to replace the pump. The pump is located on the motor and is attached by two clips. This part is white in color, made from plastic and is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Easy Part #:

EAP11741239

Availability:

In Stock

Price:

$39.65

Suspension spring

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Easy Part #:

EAP11743345

Availability:

In Stock

Price:

$6.43

Clutch assembly (complete clutch assembly)

The clutch assembly is used on direct drive washing machines and helps spin the basket during the spin cycle to remove water from the tub. If your clutch is worn out it can cause the washer to be noisy or leave water in the tub because it won’t drain properly, which will leave your clothes soaked. The clutch assembly includes a brake cam driver, retaining ring, bearing, and a spring, depending on your model number. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the washer before starting your repair.

Easy Part #:

EAP334641

Availability:

In Stock

Price:

$22.07

Water inlet valve with mounting bracket (inlet water valve kit)

The water fill valve kit attaches the water lines on the back of your washer. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. This kit includes a blue body fill valve, a mounting bracket and a screw. The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads. This is a genuine OEM part. Please remember to disconnect the power and the water supply before starting your repair.

Easy Part #:

EAP334646

Availability:

In Stock

Price:

$29.15

Agitator bolt (screw)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Easy Part #:

EAP11741866

Availability:

In Stock

Price:

$7.02

Tub spring (spring)

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be noisy and off balance during the spin cycle. Please check your model to see how many springs are required for your model. The spring is sold individually. This is a genuine OEM part. Please make sure you disconnect the power to the washer before starting your repair.

Easy Part #:

EAP11751118

Availability:

In Stock

Price:

$4.38

Centerpost gasket (gasket)

Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.

Easy Part #:

EAP11723081

Availability:

In Stock

Price:

$5.62

Thrust spacer (washer)

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is approximately 2 1/2-inch in diameter. The thrust spacer is used in the agitator assembly between the agitator and the auger. The thrust spacer supports the agitator auger as it moves. It is used in many direct drive washer machine models. If your washer will not agitate or is noisy, you may need to replace the thrust spacer. Please be sure to disconnect the power to your washer before starting your repair. You may need agitator grease for the repair. This is a genuine OEM part.

Easy Part #:

EAP334562

Availability:

In Stock

Price:

$4.42

Lid switch

This is a replacement lid switch for your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

Easy Part #:

EAP11722098

Availability:

In Stock

Price:

$37.79

Fabric softener dispenser

This parts fits on top of the agitator.

Easy Part #:

EAP11743341

Availability:

In Stock

Price:

$11.67

Screw, 8/18 x 3/8 (screw 8pk)

This screw is sold individually.

Easy Part #:

EAP11746840

Availability:

In Stock

Price:

$6.52

Gearcase (complete transmission assembly)

This is used in your direct drive washer that has a neutral drain.

Easy Part #:

EAP341974

Availability:

In Stock

Price:

$179.29

Foot, front - single (foot, leveling)

The adjustable leveling leg is used to support and keep your washer level. It also allows you to adjust the height of your washer. If your washer is shaking, vibrating, or moving during operation you may need to replace this part. This part has a rubber foot, almost 3” long and is made of metal and rubber. This is a genuine OEM part and is sold individually.

Easy Part #:

EAP11747965

Availability:

In Stock

Price:

$4.38

1-15 of 167