Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

11015942400 Kenmore Washer Parts List

1-15 of 211

Agitator directional cogs (dog, agitator (4))

These agitator directional cogs are commonly referred to as dog ears. They come four in a package and are usually used with direct drive washing machines. When the teeth on the outer edge are worn down the cogs will not engage with the upper agitator, causing it not to agitate properly. It is recommended to replace all four at the same time. These agitator directional cogs are ?-inch high and 1-inchlong and they are a genuine OEM part.

Easy Part #:

EAP388034

Availability:

In Stock

Price:

$4.34

Direct drive motor coupling (coupling, motor)

The newer version of the coupler kit is made with new metal sleeves for added strength. This part is located between the motor and transmission on the direct drive washer that does not have a belt. The coupler will break to protect the motor from damage if the drive motor system seizes up. If your washer will not fill, will not agitate or spin, but it will drain the water from the tub, you may need to replace this part because it has failed. This is a genuine OEM part. Disconnect the power to your washer before starting the repair.

Easy Part #:

EAP1485646

Availability:

In Stock

Price:

$21.18

Direct drive water pump (pump (complete))

This pump is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one. This part is used to remove water from the tub during the drain cycle. If your washer is leaking, not draining, pumps but will not spin or fills and drains at the same time you may need to replace the pump. The pump is located on the motor and is attached by two clips. This part is white in color, made from plastic and is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Easy Part #:

EAP11741239

Availability:

In Stock

Price:

$39.65

Suspension spring (spring, suspension (3))

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Easy Part #:

EAP11743345

Availability:

In Stock

Price:

$6.43

Agitator bolt (screw & washer asm)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Easy Part #:

EAP11741866

Availability:

In Stock

Price:

$7.02

Centerpost gasket (gasket, centerpost)

Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.

Easy Part #:

EAP11723081

Availability:

In Stock

Price:

$5.62

Seal, inner cap (seal, agitator cap)

Also known as an O-Ring. This black o-ring seal is three inches in diameter.

Easy Part #:

EAP11748108

Availability:

In Stock

Price:

$6.43

Screw, 8/18 x 3/8 (screw, 8-18 x 3/8)

This screw is sold individually.

Easy Part #:

EAP11746840

Availability:

In Stock

Price:

$6.52

Gearcase (gearcase (complete) (refer to page 15 for further breakdown))

This is used in your direct drive washer that has a neutral drain.

Easy Part #:

EAP341974

Availability:

In Stock

Price:

$179.29

Foot, front - single (foot, front (2))

The adjustable leveling leg is used to support and keep your washer level. It also allows you to adjust the height of your washer. If your washer is shaking, vibrating, or moving during operation you may need to replace this part. This part has a rubber foot, almost 3” long and is made of metal and rubber. This is a genuine OEM part and is sold individually.

Easy Part #:

EAP11747965

Availability:

In Stock

Price:

$4.38

Lid seal (seal, lid)

This part is the replacement lid seal for your washer. It is made of rubber and is gray in color. It is approximately 21 inches long and 1 inch wide. The washer lid seal creates a seal for your top load washer and prevents leaks. If your washer is leaking from the lid, or if you are having difficulty closing the washer lid, the lid seal may need to be replaced. The lid seal will also need to be replaced if it is worn out or damaged. This part is sold individually and is sourced directly from the manufacturer. This is an authentic OEM part.

Easy Part #:

EAP11744855

Availability:

Special Order

Price:

$54.52

Lid hinge mounting screw (screw, lid hinge mounting (4))

Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.

Easy Part #:

EAP11748588

Availability:

In Stock

Price:

$7.15

Drain hose (anchored drain hose assembly)

It connects from the pump to the back panel. The clamp is not included.

Easy Part #:

EAP11753688

Availability:

In Stock

Price:

$25.98

Hose clamp (clamp, hose)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Easy Part #:

EAP11743008

Availability:

In Stock

Price:

$6.49

Easy Part #:

EAP11746362

Availability:

In Stock

Price:

$6.47

1-15 of 211