11021182010 Kenmore Washer Parts List

Agitator directional cogs (use wpl 80040)

These agitator directional cogs are commonly referred to as dog ears. They come four in a package and are usually used with direct drive washing machines. When the teeth on the outer edge are worn down the cogs will not engage with the upper agitator, causing it not to agitate properly. It is recommended to replace all four at the same time. These agitator directional cogs are ?-inch high and 1-inchlong and they are a genuine OEM part.

Lid latch assembly (use wpl w10404050)

The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.

Agitator repair kit

This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover). This part has been updated by the manufacture.

Washing machine suspension rod kit (use wpl w10349191)

Thrust spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is approximately 2 1/2-inch in diameter. The thrust spacer is used in the agitator assembly between the agitator and the auger. The thrust spacer supports the agitator auger as it moves. It is used in many direct drive washer machine models. If your washer will not agitate or is noisy, you may need to replace the thrust spacer. Please be sure to disconnect the power to your washer before starting your repair. You may need agitator grease for the repair. This is a genuine OEM part.

Screw, 8/18 x 3/8 (screw)

This screw is sold individually.

Touch-up paint - white

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Lid bumper

This single gray and white washer lid bumper contains a rubber bottom to help cushion the lid as it closes against the cabinet lid. If your bumper is missing you should replace the part to avoid metal on metal causing damage to the top of the washer. This is a genuine OEM part and is sold individually.

Shift actuator - 120v 60hz

This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.

Drive belt

The main drive belt is designed to ride on the pulley until the basket gets up to speed.

Washer drive pulley (use wpl w10315818)

This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the splines on the clutch assembly are stripped and the washer is making noise, or if you are having problems with the wash and spin cycles. You will need to access the bottom of the washer for this repair. It is easiest to if you disconnect your washer from both the water and power source, and lay it on its back. The clutch assembly contains 6 parts, and all are included with the kit. It is also important to change out the entire assembly, rather than individual pieces.

Lid hinge mounting screw (use wpl w10119828)

Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.

Hose clamp (use wpl 596669)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

D-shaped knob insert

This insert is sold individually. Knob not included. Knob is sold separately.

Lid hinge bearing

This is the bearing for the lid hinge. Sold individually.