11021392011 Kenmore Washer Parts List

Lid latch assembly (latch)

The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.

Washing machine suspension rod kit (suspension)

Screw, 8/18 x 3/8 (screw 8pk)

This screw is sold individually.

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Lid bumper (bumper, lid)

This single gray and white washer lid bumper contains a rubber bottom to help cushion the lid as it closes against the cabinet lid. If your bumper is missing you should replace the part to avoid metal on metal causing damage to the top of the washer. This is a genuine OEM part and is sold individually.

Shift actuator - 120v 60hz (actuator)

This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.

Drive belt (belt)

The main drive belt is designed to ride on the pulley until the basket gets up to speed.

Washer drive pulley (cam)

This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the splines on the clutch assembly are stripped and the washer is making noise, or if you are having problems with the wash and spin cycles. You will need to access the bottom of the washer for this repair. It is easiest to if you disconnect your washer from both the water and power source, and lay it on its back. The clutch assembly contains 6 parts, and all are included with the kit. It is also important to change out the entire assembly, rather than individual pieces.

Lid hinge mounting screw

Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.

Hose clamp (clamp)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

D-shaped knob insert (spring clip)

This insert is sold individually. Knob not included. Knob is sold separately.

Lid hinge bearing (bearing, lid hinge)

This is the bearing for the lid hinge. Sold individually.

Washer

This part goes on the agitator retaining bolt.

Lid latch strike (strike)

This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, your washer door may not close properly and you may not be able to run your washer. The latch is found under the lid and can be screwed out and replaced. You will need a Phillips-head screwdriver for this repair. This part is sold individually and is and OEM part from the manufacturer.

Spray paint - 12 oz. - white (spray)

Spray paint is designed to help cover up any scratches or chips on your appliances. This spray pant is white in color and comes in a 12 oz aerosol can. Please make sure to clean the area that requires touch up to avoid any old paint or dirt getting into the fresh paint. When using the spray paint it is recommended to wear gloves and a protective mask. Make sure to shake the can well before using and to spray a few inches away from the surface for best results. Please wait until the paint is dried before using the appliance. This is a genuine OEM part.