Parts for Kenmore Models 11067741600

Dryer thermal fuse (non-resettable thermal fuse)

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Easy Part #:: EAP11741460

Availability:: In Stock

Price:: $16.60

Dryer door switch (door switch)

This 3-wire with leads dryer door switch is an on and off mechanism that prevents the dryer from operating while the door is open. The dryer will not operate until the door switch signals that the dryer door is closed. If the dryer won’t start, the lever broke off, or the switch shorted out, the appliance will not operate and the part will need to be replaced. This switch is a genuine OEM part and replaces the 2-wire switch. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741701

Availability:: In Stock

Price:: $22.07

Dryer cycling thermostat (internal bias operating thermostat)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock

Price:: $21.58

Door catch kit (door latch kit)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock

Price:: $3.66

Dryer heating element (element)

When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.

Easy Part #:: EAP11741416

Availability:: In Stock

Price:: $44.45

Dryer drum support roller (support)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Easy Part #:: EAP11752609

Availability:: In Stock

Price:: $17.44

Idler pulley

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:: EAP334244

Availability:: In Stock

Price:: $25.38

Lint filter (lint screen)

This filter collects lint as it passes through the dryer vent.

Easy Part #:: EAP1491676

Availability:: In Stock

Price:: $50.66

Thermal cut-off kit (thermal cut-off fuse kit)

This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.

Easy Part #:: EAP334278

Availability:: In Stock

Price:: $35.87

Leveling foot (leveling feet)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Easy Part #:: EAP1609293

Availability:: In Stock

Price:: $5.16

Roller support tri-ring (ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11755850

Availability:: In Stock

Price:: $6.23

Drive belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide. This drive belt is 93 1/2 inches long, and 1/4 of an inch wide, with 4 ribs and 3 grooves. To complete this repair, you will need a Phillips screw driver, a 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Make sure to disconnect power to the dryer before beginning this repair.

Easy Part #:: EAP11722115

Availability:: In Stock

Price:: $21.87

Thrust washer

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11740482

Availability:: In Stock

Price:: $4.54

Dryer repair kit (repair-dyr)

This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings, and one washer. This universal maintenance kit is an all-encompassing kit for fixing a noisy dryer, among other symptoms, but noisy being the most common. It is compatible with 27-inch wide dryers built from 1965 onwards. Be sure to disconnect the dryer or shut off the house circuit breaker for the appliance before you begin your repair. To access these parts, you will need to remove the dryer drum. For this installation you will need a 1/4-inch nut driver, a long flat-blade screwdriver, a short flat-blade screw diver, and a Phillips screwdriver.