Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

11078062801 Kenmore Dryer Parts List

1-15 of 168

M series new style coil kit (valve coil kit)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP334310

Availability:

In Stock - Ships Today

Price:

$22.74

Dryer drum support roller (support)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Easy Part #:

EAP11752609

Availability:

In Stock - Ships Today

Price:

$17.44

Lint filter (lint screen)

This filter collects lint as it passes through the dryer vent.

Easy Part #:

EAP1491676

Availability:

In Stock - Ships Today

Price:

$50.66

Igniter kit (glow bar igniter)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:

EAP334180

Availability:

In Stock - Ships Today

Price:

$28.31

Door catch (catch)

This door catch helps to keep the door closed when the machine is in use.

Easy Part #:

EAP11748369

Availability:

In Stock - Ships Today

Price:

$4.84

Leveling foot (leveling feet)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Easy Part #:

EAP1609293

Availability:

In Stock - Ships Today

Price:

$5.16

Roller support tri-ring (ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:

EAP11755850

Availability:

In Stock - Ships Today

Price:

$6.23

Thermostat, internal-bias (thermistor)

This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Easy Part #:

EAP11746740

Availability:

In Stock - Ships Today

Price:

$36.65

Dryer radiant flame sensor (radiant sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:

EAP11741429

Availability:

In Stock - Ships Today

Price:

$32.53

Light bulb - 10w (10-watt lamp)

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Easy Part #:

EAP11739347

Availability:

In Stock - Ships Today

Price:

$16.26

Disposable thermal fuse - two terminal (non-resettable thermal fuse)

This part attaches to the exhaust duct of your clothes dryer.

Easy Part #:

EAP11741444

Availability:

In Stock - Ships Today

Price:

$15.45

Moisture sensor (electrode)

This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.

Easy Part #:

EAP11741408

Availability:

In Stock - Ships Today

Price:

$7.05

Screw, 8/18 x 3/8 (screw 8pk)

This screw is sold individually.

Easy Part #:

EAP11746840

Availability:

In Stock - Ships Today

Price:

$6.52

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Easy Part #:

EAP385132

Availability:

In Stock - Ships Today

Price:

$6.96

Screw - 10-16 x 1 (screw)

This screw is sold individually.

Easy Part #:

EAP11741409

Availability:

In Stock - Ships Today

Price:

$7.36

1-15 of 168