11087561602 Kenmore Dryer Parts List

Dryer thermal fuse (non-resettable thermal fuse)

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Door catch kit (door latch kit)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Dryer drum support roller (support)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Idler pulley

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Leveling foot (leveling feet)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Roller support tri-ring (ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Drive belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide. This drive belt is 93 1/2 inches long, and 1/4 of an inch wide, with 4 ribs and 3 grooves. To complete this repair, you will need a Phillips screw driver, a 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Make sure to disconnect power to the dryer before beginning this repair.

Thermostat, internal-bias (thermistor)

This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Thrust washer

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Dryer heater element (element)

High limit thermostat and thermal cut-off kit (thermal cut-off fuse kit)

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.

Light bulb - 10w (10-watt lamp)

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Heating element connection wire kit (wire replacement kit)

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Screw, 8/18 x 3/8 (screw 8pk)

This screw is sold individually.

Dryer drum seal with adhesive (seal)

This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.