Parts for Kenmore Models 11088762791

Agitator directional cogs (dog, agitator (4))

These agitator directional cogs are commonly referred to as dog ears. They come four in a package and are usually used with direct drive washing machines. When the teeth on the outer edge are worn down the cogs will not engage with the upper agitator, causing it not to agitate properly. It is recommended to replace all four at the same time. These agitator directional cogs are ?-inch high and 1-inchlong and they are a genuine OEM part.

Easy Part #:: EAP388034

Availability:: In Stock - Ships Today

Price:: $4.34

Direct drive motor coupling (coupling, motor and isolating)

The newer version of the coupler kit is made with new metal sleeves for added strength. This part is located between the motor and transmission on the direct drive washer that does not have a belt. The coupler will break to protect the motor from damage if the drive motor system seizes up. If your washer will not fill, will not agitate or spin, but it will drain the water from the tub, you may need to replace this part because it has failed. This is a genuine OEM part. Disconnect the power to your washer before starting the repair.

Easy Part #:: EAP1485646

Availability:: In Stock - Ships Today

Price:: $21.18

Thermal cut-off kit (thermal cutoff)

This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. This genuine OEM kit also includes flat heaters with jumper wires. Make sure to disconnect the power source to the dryer before beginning this repair.

Easy Part #:: EAP334299

Availability:: In Stock - Ships Today

Price:: $33.22

Dryer cycling thermostat (thermostat, internal-bias)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock - Ships Today

Price:: $21.58

Door catch kit (strike, panel)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock - Ships Today

Price:: $3.66

Suspension spring (spring, suspension (3))

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Easy Part #:: EAP11743345

Availability:: In Stock - Ships Today

Price:: $6.43

Dryer drum support roller (support, roller)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Easy Part #:: EAP11752609

Availability:: In Stock - Ships Today

Price:: $17.44

Clutch assembly (clucth (complete))

The clutch assembly is used on direct drive washing machines and helps spin the basket during the spin cycle to remove water from the tub. If your clutch is worn out it can cause the washer to be noisy or leave water in the tub because it won’t drain properly, which will leave your clothes soaked. The clutch assembly includes a brake cam driver, retaining ring, bearing, and a spring, depending on your model number. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the washer before starting your repair.

Easy Part #:: EAP334641

Availability:: In Stock - Ships Today

Price:: $22.07

Idler pulley (pulley, idler)

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:: EAP334244

Availability:: In Stock - Ships Today

Price:: $25.38

Water inlet valve with mounting bracket (valve, water mixing)

The water fill valve kit attaches the water lines on the back of your washer. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. This kit includes a blue body fill valve, a mounting bracket and a screw. The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads. This is a genuine OEM part. Please remember to disconnect the power and the water supply before starting your repair.

Easy Part #:: EAP334646

Availability:: In Stock - Ships Today

Price:: $29.15

Roller support tri-ring (tri-ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11755850

Availability:: In Stock - Ships Today

Price:: $6.23

Thrust washer (washer, thrust)

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11740482

Availability:: In Stock - Ships Today

Price:: $4.54

Agitator bolt (screw)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Easy Part #:: EAP11741866

Availability:: In Stock - Ships Today

Price:: $7.02

Tub spring (spring, counterweight)

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be noisy and off balance during the spin cycle. Please check your model to see how many springs are required for your model. The spring is sold individually. This is a genuine OEM part. Please make sure you disconnect the power to the washer before starting your repair.