25326092100 Kenmore Freezer Parts List

Freezer door key (key)

This white plastic freezer door key is used for most upright or chest freezers. If your door key becomes broken or lost it will need to be replaced. This is a genuine OEM part. It is sold individually.

Freezer door gasket (door gasket)

Refrigerator ice maker assembly (ice maker mold)

The ice maker assembly is used to produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4 pin wire harness adapter and tube. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Replacement ice maker (ice maker motor)

This ice maker is the replacement heat-release unit only. This kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female and one round male connectors. This is a genuine OEM part. Please make sure you disconnect the power to the refrigerator before starting your repair.

Water inlet valve (water valve)

When energized, the water inlet valve will release water from the supply line into the ice mold and the water dispenser in the refrigerator. If the ice maker is not making or dispensing ice, not dispensing water, or leaking, you may need to replace the water inlet valve. The water inlet valve is in the back section of your refrigerator and will need to be pulled out from the wall. Make sure to disconnect both the water and power supply before starting your repair.

Defrost thermostat (thermostat)

The defrost thermostat snaps onto the top portion of the evaporator, it acts as a safety device and protects the evaporator from overheating during the defrost cycle. The thermostat can sense the rise in the evaporator temperature during the defrost cycle and cycles the defrost heater off after all the frost is melted from the coils. The defrost thermostat may need to be replaced if the appliance is experiencing temperature-related issues such as: too cold, too warm, frost buildup, not running, or running too long. This is a genuine OEM part. It is recommended to disconnect the power to your appliance before starting your repair.

Screw

This small, Phillips-head screw works with your refrigerator/freezer. It screws in to the freezer door and connects to the door handle. This part is made of stainless steel and is sold individually. This is an OEM part sourced directly from the manufacturer.

Run capacitor - 120v (capacitor)

The run capacitor is attached to the compressor. This part is 120 volts and 15 mfd. The run capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Adjustable leveling foot - black (adjustable foot)

Sold Individually.

Gasket retainer clip kit - 24 pieces (panel screw)

These are used to hold your gasket in place.

Fan motor evap 115v (motor)

The 115-volt evaporator fan motor is in the back of the freezer section and circulates air over the coils. These coils will convert the heat into cool air, which is then circulated. If your freezer is noisy or too warm from the motor not working, you will need to replace this part. It is suggested to replace the thermistor when replacing the evaporator fan. This is a genuine OEM part – note the screw holes in the motor are not threaded from the factory, use your old screws. Please remember to disconnect the power to the refrigerator before starting your repair.

Handle mounting block (block)

Sold individually.

Evaporator fan blade (refrigerator evaporator fan blade)

If your refrigerator or freezer is too warm or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate the cold air into the refrigerator and freezer sections. The fan blade is white in color and made from plastic. This is a genuine OEM part. Please be sure to disconnect the power to your refrigerator before starting your repair.

Icemaker assembly (icemaker)

This icemaker is used on newer models where the cord will plug directly in to the back of the freezer. It includes the cover, fill cup, bail arm and a four-pin plug harness.

Refrigerator light bulb (light bulb/l)