36362702200 Kenmore Microwave Parts List

Light bulb - 40w 130v (lamp - cavity)

This 40 watt, 130-volt clear appliance light bulb is for your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open or below the microwave to provide light for the cooking area. It is clear in color and has a small screw-in base. If your current bulb is burnt out or broken you will need to replace it. This bulb is a genuine OEM part and is sold individually.

Drive motor (motor turntable)

This motor rotates the glass turntable in the microwave to aid in even cooking temperatures. If your cooking tray is not rotating or making noises you may need to replace the motor. This motor accepts a D-shaped shaft, has 21 volts, and is a genuine OEM part. Please remember to disconnect the power to the microwave before starting the repair.

Light socket - 250v 75w (socket lamp)

This 250-volt 75 watt light socket is located inside the microwave to provide power to the light while holding the light bulb in place. If the light bulb is not working, the switch might have failed and will need to be replaced. The light bulb is not included and must be ordered separately. The socket is black in color and measures a little over 2” long. Please remember to disconnect power to the microwave before starting the repair. This is a genuine OEM part.

Cooking tray (tray-cooking)

This glass cooking tray provides a levelled cooking surface and rotates in your microwave to ensure even cooking temperatures once the door is closed and the timer has been set. If your tray is broken or cracked it is recommended to replace it. This tray measures 12.5-inch in diameter, which might be smaller than the original tray, is made from glass and is a genuine OEM part. No tools are required for this repair.

Secondary door switch (switch-micro)

The secondary door switch, also known as a micro switch, works in conjunction with your microwave by monitoring the door latch position and sending communication to the electronic control board to let it know if the latch is open or closed. When the door is shut, the door switch will close to send power to the microwave to operate. If the microwave won’t start, the switch has failed, and the part will need to be replaced. You can test the switch for continuity. This part measures 1.5” L x .75” W. Due to the high voltage capacitor in the microwave, it can retain a lethal electrical charge, even when unplugged, it is suggested to have a service technician install the part. Please disconnect power to the microwave before beginning the repair. This is a genuine OEM part.

Turntable coupler (coupler-tt)

This turntable motor coupler connects the turntable motor to the turntable tray to activate the tray. If your tray does not consistently turn or does not turn at all, replace this part. This part measures 1 1/2" in diameter. Remember to unplug your microwave from the power source as a safety precaution. Refer to the openers manual provided by the manufacturer for further installation instructions and accurate guidance.

Fuse

The line fuse, also known as a ceramic fuse, is used to protect your microwave when there is a power serge by shutting down the microwave to avoid damage. If your microwave has no heat, won’t turn on, or the touch pad is not working properly, you may need to replace the fuse. This part measures approximately 1.25” long and is sold individually. Please remember to disconnect power to the microwave before starting the repair. This is a genuine OEM part.

Monitor door switch (switch-micro)

The door interlock switch (normally closed) works in conjunction with your microwave operation. The switch will prohibit the microwave from starting when the microwave door is open. If your microwave won’t turn on or there is no heat you may need to replace the switch. This part measures 1.5” L x .75” W, 250 volts, is black in color with a red dot and is sold individually. Please remember to disconnect the power before starting your repair. This is a genuine OEM part.

Charcoal filter (filter-charcoal)

This vent hood filter collects grease particles in the air from cooking. Sold individually.

Door handle (handle)

Screws NOT included.

Flat cab mounting bolt (bolt-flat)

The flat cab mounting bolt is used to secure your microwave to your cabinet. The bolt is approximately 4 inches long. The main reason you would need to replace this bolt is if the old bolt is stripped or missing, and the microwave will not stay secure in the cabinet. This is a genuine OEM part and it is sold individually.

Aluminum grease filter (filter grease)

This aluminum filter collects grease particles in the air from cooking. Sold individually.

Turntable roller guide (roller guide ring)

This roller guide sits underneath the glass turntable tray.

Microwave mounting plate (plate mounting ass'y)

This plate mounts the microwave under the cabinet.

Grille screw (screw - grille)