41788980100 Parts List

1-15 of 173

Rear drum bearing kit (dryer rear drum bearing kit. The holes in the metal plate are not threaded. Use the self tapping screws in the kit to thread the plate.)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:

EAP459829

Availability:

On Order

Price:

$17.12

Drum support bearing (rear bearing support for dryer drum.)

The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is making unusual noises or will not tumble, you may need to replace this part. It is white in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP418807

Availability:

In Stock

Price:

$3.25

Lint screen and frame (lint filter screen and mounting frame)

This filter collects lint as it passes through the dryer vent.

Easy Part #:

EAP417677

Availability:

No Longer Available

M series ignition coil kit (dryer gas valve solenoid coil kit. The kit includes both 2 and 3 wire coils. If the dryer does not heat or heats intermittently the gas valve coils ma)

The gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If it takes too long to dry or there is no heat, the coils may be bad and will need to be replaced. When the coils go bad they will not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP470049

Availability:

In Stock

Price:

$16.43

Thermal limiter - limit 220 (dryer thermal limiter (or thermal fuse). Located on the blower housing. If the dryer overheats, the thermal fuse blows to cut off power to the dryer.)

This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out. If your dryer overheats, will not start, takes too long to dry, or has no heat or not enough heat, you will need to replace the fuse because it cannot be reset. This is a genuine OEM part. It is recommended to disconnect the power to your dryer before starting your repair.

Easy Part #:

EAP419402

Availability:

In Stock

Price:

$9.17

Idler pulley assembly (idler tension pulley with bracket for dryer drum belt)

The idler pulley assembly provides the tension required for a flat belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel. If your dryer is noisy or will not tumble you may need to replace the idler pulley. This is a genuine OEM part.

Easy Part #:

EAP457526

Availability:

No Longer Available

Dryer drum bearing bracket (bracket bearing support)

This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing

Easy Part #:

EAP12579101

Availability:

On Order

Price:

$5.75

Easy Part #:

EAP459766

Availability:

In Stock

Price:

$9.27

Flame sensor (Flame sensor for gas dryer)

This part senses the flame for heat allowing the gas valve to open.

Easy Part #:

EAP459818

Availability:

In Stock

Price:

$18.74

Easy Part #:

EAP475419

Availability:

In Stock

Price:

$3.30

Front drum seal (front lower felt seal, drum)

Used with dryers with a 27-inch drum.

Easy Part #:

EAP459776

Availability:

On Order

Price:

$13.53

Igniter (gas dryer igniter)

This part ignites the gas within the dryer. Be sure to not handle this igniter by the gray part as it is very fragile.

Easy Part #:

EAP900236

Availability:

On Order

Price:

$36.30

High temperature adhesive (high temperature adhesive for installing rubber and felt seals)

The high temperature adhesive is used to create a heat resistant bond between felt seals and rubber gaskets on your appliance. This adhesive is made to withstand hot temperatures. This tube contains one ounce of adhesive. Before starting your repair, it is recommended to wear gloves and ensure that your working area is clean and dry.

Easy Part #:

EAP474458

Availability:

On Order

Price:

$32.66

1-15 of 173