Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

41790412700 Kenmore Dryer Parts List

1-15 of 102

Rear drum bearing kit (bearing)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:

EAP459829

Availability:

In Stock

Price:

$52.07

Drum belt (belt)

This dryer drum belt is 88 3/4 inches long, and is 1/4 inch wide. The belt attaches to the motor pulley and helps rotate the drum as the motor rotates. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP1148434

Availability:

In Stock

Price:

$14.30

Drum support bearing (bearing drum)

The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is making unusual noises or will not tumble, you may need to replace this part. It is white in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP418807

Availability:

In Stock

Price:

$5.21

Drum glide - white (glide drum)

The white drum glide supports the drum on the front side and helps rotate smoothly and quietly while operating. If your dryer won’t tumble or is noisy, the drum glide may be worn down causing a metal on metal noise. Your dryer requires two glides; it is recommended to replace both glides at the same time. The drum glide is a genuine OEM part and is sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:

EAP5574052

Availability:

In Stock

Price:

$27.92

Door catch

The door catch helps keep the door closed while the machine is running. If your dryer will not start or the door will not close, you may need to replace the door catch. This is a genuine OEM part. Please remember to disconnect the power to your dryer before you start the repair.

Easy Part #:

EAP418433

Availability:

In Stock

Price:

$61.61

Lower front felt seal with adhesive (felt)

The lower drum felt seal is used to help the drum glide smoothly on the front panel. If your dryer takes too long to dry or is noisy while the dryer drum is spinning, you may need to replace the seal. The seal measures approximately 47” L x 1” W and the adhesive is included. Please disconnect the power to the dryer before beginning the repair. This is a genuine OEM part.

Easy Part #:

EAP832645

Availability:

In Stock

Price:

$19.78

Turn - type start switch (switch)

This part is used to start the dryer once you have selected a setting on the timer.

Easy Part #:

EAP975832

Availability:

In Stock

Price:

$48.84

M series ignition coil kit (coils (sec &)

The gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If it takes too long to dry or there is no heat, the coils may be bad and will need to be replaced. When the coils go bad they will not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP470049

Availability:

In Stock

Price:

$19.63

Blower housing with blower wheel (asmy-blwr hs)

The blower wheel and housing assembly attaches to the drive motor shaft, blows the air through the drum and out through the exhaust. If the dryer is taking too long to dry, is noisy, or there is no air flow during operation, then the blower wheel could be damaged or broken and will need to be replaced. This part is white in color and made of plastic. This blower wheel and housing assembly will fit 471 series Kenmore eclectic or gas dryers. Will also fit some Frigidaire, Crosley, Gibson and White Westinghouse gas or electric dryers. Please check your model number. Please be sure to disconnect the power to your dryer before starting your repair. This is a genuine OEM part.

Easy Part #:

EAP418726

Availability:

In Stock

Price:

$92.89

Easy Part #:

EAP425733

Availability:

In Stock

Price:

$16.94

Dryer drum bearing bracket (bracket)

This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing

Easy Part #:

EAP12579101

Availability:

In Stock

Price:

$10.04

Lint filter (lint trap)

This white dryer lint filter screen collects lint as it passes through the dryer vent.

Easy Part #:

EAP417841

Availability:

In Stock

Price:

$22.24

Drive motor with pulley (motor)

This motor has a double shaft.

Easy Part #:

EAP418132

Availability:

In Stock

Price:

$156.96

Door handle (handle)

This part is the replacement door handle for your dryer. It is made of white plastic and measures about 2 ½ inches long and 4 inches wide. The door handle allows you to open and close the dryer door. If it is cracked, damaged, or missing, this is the part that will replace it. Many of our customers rated this repair easy, as the new handle should simply snap into place. This is an OEM part sourced directly from the manufacturer.

Easy Part #:

EAP418388

Availability:

In Stock

Price:

$47.64

Upper front felt seal (upper felt seal)

This part is the replacement upper front felt seal for your dryer. It is made of felt and is approximately 17 inches long and 1 inch wide. The felt seal allows the drum to glide smoothly on the front panel. If your dryer is noisy, will not tumble, or leaves marks on your clothes after the drying cycle, you may need to replace the upper front felt seal. This part is sold individually, so if you do not have any high-temperature adhesive, you will need to order that as well. Be sure to clean all the residue from your previous felt seal before you install the new one. This ensures a secure fit. This is an OEM part sourced directly from the manufacturer.

Easy Part #:

EAP975866

Availability:

In Stock

Price:

$36.13

1-15 of 102