41793802201 Kenmore Washer Dryer Combo Parts List

Front upper felt seal with adhesive (seal,felt ,upper)

The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so that heat remains in the dryer while it tumbles. If your old upper felt seal is coming apart, you notice that hot air is leaking out the dryer door, or your clothes are taking too long to dry, you may need to replace the seal. When you order this part, it comes with the upper felt seal, as well as the required high-temperature adhesive.

Tub seal assembly (seal assy,tub ,transmission)

This tub seal helps prevent any leaking around the transmission of your washer. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Screw (screw,10-16ab x 0.500)

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Screw (screw,10-16ab x 0.375)

Sold individually.

Washer lid lock with external safety switch (lock,lid ,w/ext switch)

Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).

Door strike

The door strike works in conjunction with the dryer door. The male piece of the door strike is the piece that activates the door switch once the dryer door is closed. If your dryer won’t start, or the door won’t open/close, you may need to replace the door strike. This part is made from metal and measures approximately 1 inch. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Dual action agitator (agitator assy,dual action)

Tension idler pulley (idler arm assy,vaw ,with pulley)

This idler arm assembly comes with the pulley wheel.

Blower wheel

This blower wheel is a genuine OEM replacement part for your dryer. The wheel can become damaged through use of the dryer, especially if the drive motor shaft, which it is attached to, becomes damaged. This repair will require some disassembly of the dryer. Make sure to disconnect the power source and wear appropriate work gloves while conducting this repair.

Start switch (switch,start ,turn type)

This start switch is a manufacturer-approved replacement part for your dryer. A faulty start switch means your dryer will not begin its drying cycle. In order to complete this repair, you will need a Phillips screwdriver. Once you access the switch, disconnect the two wire leads and attach them to the new switch. Make sure to disconnect power to the unit before beginning this repair, and wear work gloves.

Drain hose (hose,drain)

Idler arm assembly (idler arm assy,with pulley)

This idler pulley assembly is a manufacturer-approved replacement part for your washer/dryer. The assembly includes the idler pulley and arm. The idler pulley provides tension for the belt to rotate the drum. You may notice your idler pulley making a sqeaking or squealing noise, signalling that it needs to be replaced.

Agitator drive block (hub,drive ,agitator)

The agitator drive block works in conjunction with the agitator in your washing machine by rotating the agitator assembly. If your washer is noisy and not agitating, you may need to replace the drive block because it may be worn out. This part is located between the agitator and the transmission shaft, measures approximately 2” long and is made of metal. This is a genuine OEM part. Please remember to disconnect the power and water supply before beginning your repair.

Single clip (clip,guide ,(3))

Sold individually.

Spin bearing (bearing,outer tub)

The upper spin bearing works in conjunction with your washer. This part is located on the bottom of the outer tub where the transmission goes up through the middle of the tub. The spin bearing is used to support the transmission shaft in the drive system and allows the transmission shaft to be able to spin freely during the spin cycle. When the spin bearing goes bad it can cause noises during the spin cycle and will need to be replaced. This part is made of metal and is secured by mounting screws. The screws are not included, bearing only. This is a genuine OEM part. Please disconnect the water and power supply before starting the repair.