58714013401 Kenmore Dishwasher Parts List

Dishwasher bottom door gasket (gasket)

This gasket goes on the bottom of the dishwasher door to create a tight seal between the tub and the outer edge of the door. If the gasket is cracked or broken, it will need to be replaced to keep water from leaking out on to the floor. The gasket is approximately 23” long and is a genuine OEM part. It is recommended that once you have installed the gasket to leave the door closed for a few hours to make sure the gasket is properly sealed.

Dishwasher tub gasket - gray (gasket)

The door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking you may need to replace the door gasket. This gray door gasket is made of rubber and is a genuine OEM part.

Wheel & bushing ass (lower rack roller and shaft assembly)

The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is made of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it. Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.

Spray arm

Roller tub gray (roller)

The dishrack support roller attaches to the inside of the tub by a screw, to help support the upper rack. There are eight total inside the tub, four on each side. This support roller is made of plastic and is approximately 1 1/2” in diameter. The screw is not included with the roller, you can reuse the existing screw. This is a genuine part and is sold individually.

Water inlet valve - 120v 60hz (valve)

This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the front of your dishwasher. The attaching solenoids on the valve open and close to release the desired amount of water needed in your dishwasher. If your dishwasher is leaking, will not fill with water, is not draining, or not cleaning the dishes properly, you may need to replace the water inlet valve. This valve has 120 volts and 60 Hz. Please be sure to disconnect the power to your dishwasher before starting your repair. This water inlet valve is a genuine OEM part.

Heating element brass nut (heating element mounting nut)

The heating element nut is used to install and secure the heating element in your dishwasher. If your dishwasher is leaking you may need to replace the nut. The manufacturer suggests replacing replace both nuts at the same time. This heating element nut is a genuine OEM part and is sold individually.

Dishwasher drain hose (hose)

The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage by carrying the drain water from the dishwasher drain pump to the kitchen sink drain. The drain hose measures 8 feet long. If your drain hose becomes damaged or cracked it will cause water to leak on the floor and you will need to replace the hose. This hose is white and black in color, made of plastic and is a genuine OEM part. Please make sure you shut off the water supply and disconnect the power to the dishwasher before starting your repair.

Door spring (spring)

Sold Individually.

Detergent and rinse dispenser with cap (dispenser)

The manufacturer has redesigned this part and it may appear different than the original, but will have the same functionality. This part releases the detergent and rinse aid into the dishwasher.

Spring linkage (spring)

This linkage attaches to the door spring.

Drain pump

The pump ejects the water from the dishwasher.

Wheel and bushing assembly (wheel bushing)

Sold Individually. Order quantity needed.

Heating element (heater)

This part is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher and is located on the bottom of the dishwasher. Grommets are included with this part.

Door strike (strike)

This door strike is mounted to the top of the dishwasher cabinet. This part catches the door handle to keep it closed.