Parts for Kenmore Models 5871440190

Roller tub gray (tub roller)

The dishrack support roller attaches to the inside of the tub by a screw, to help support the upper rack. There are eight total inside the tub, four on each side. This support roller is made of plastic and is approximately 1 1/2” in diameter. The screw is not included with the roller, you can reuse the existing screw. This is a genuine part and is sold individually.

Easy Part #:: EAP11770690

Availability:: In Stock

Price:: $12.94

Heating element brass nut (heater nut 1/2-20 brass)

The heating element nut is used to install and secure the heating element in your dishwasher. If your dishwasher is leaking you may need to replace the nut. The manufacturer suggests replacing replace both nuts at the same time. This heating element nut is a genuine OEM part and is sold individually.

Easy Part #:: EAP1524878

Availability:: In Stock

Price:: $7.27

Single door spring (door spring (includes key #4))

NOTE: Sold individually. This door spring is four and a half inches long. It is used for some dishwashers. These springs tend to wear out at the same rate, so you should replace both of your dishwasher door springs at the same time.

Easy Part #:: EAP452475

Availability:: In Stock

Price:: $31.89

Door gasket (tub gasket)

This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.

Easy Part #:: EAP452429

Availability:: No Longer Available

Upper dishrack track end cap (rack slide)

The white upper rack track stop is used to prevent the upper dish rack from sliding off the slide rail. If your rack is falling off the track, or the track stop has broken or is missing you may need to replace the track stop. This part is a genuine OEM part and is sold individually.

Easy Part #:: EAP452590

Availability:: In Stock

Price:: $33.58

Basket (silverware basket)

This is a basket for your dishwasher. It sits in the lower dishrack and holds small utensils during a washing cycle. This basket has six smaller sections where you can separate your cutlery into specific groups. This silverware holder is made entirely of plastic with a crisscross pattern allowing water and small food particles to pass through it during the cleaning process. This model is grey and roughly 14 inches long, about 6 inches high, and almost 4 inches thick.

Easy Part #:: EAP16218301

Availability:: In Stock

Price:: $26.61

Access panel screw black (screw no. 8 x 3/8" LG cr hex washer hd black)

Sold individually.

Easy Part #:: EAP649154

Availability:: In Stock

Price:: $10.81

Wash impeller (upper impeller)

This electrically operated propeller causes water to flow through your dishwasher's pump. This impeller is located above the dishwasher's mascerator blade.

Easy Part #:: EAP452583

Availability:: In Stock

Price:: $62.68

Hose clamp (clamp)

Sold individually.

Easy Part #:: EAP466832

Availability:: In Stock

Price:: $2.02

Rinse aid cap (fill plug)

This white rinse aid cap is a little over two inches long. It comes with a black rubber gasket, and is used for some dishwashers.

Easy Part #:: EAP451734

Availability:: No Longer Available

Lower rack roller assembly (wheel & bracket assy)

The lower rack wheel assembly attaches to the lower rack to allow you to slide the rack in and out easily. The wheel is white in color, made of plastic, and approximately 5 inches long. This rack wheel assembly includes two wheels and a bracket. It is a genuine OEM part and is sold individually.

Easy Part #:: EAP452142

Availability:: No Longer Available

Washer - white (washer)

Sold Individually.

Easy Part #:: EAP473211

Availability:: In Stock

Price:: $6.59

Macerator blade (macerator)

With this macerator blade it chops up/mince the food particles in the collection chamber to prevent from clogging the dishwasher pump.

Easy Part #:: EAP452585

Availability:: In Stock

Price:: $41.82

Water inlet valve (water valve)

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.