66512782K311 Kenmore Dishwasher Parts List

Door balance link kit (dishwasher door hinge cable and roller kit. Replaces right and left side.)

The door balance kit helps support the weight of the dishwasher door while it opens and closes. If the spring to the door is damaged/broken or the door is not opening and closing properly you will need to replace this part. This door kit includes 2 door balance links and 2 door balance mounts with wheels for the left and right side of the door. This is a genuine OEM part.

Mounting bracket (dishwasher upper mounting bracket. Screws sold seprately. Please see related items below.)

The mounting bracket is used to attach the dishwasher to the underside of the counter. The mounting bracket holds the dishwasher in place to keep it from moving during cycles and to keep the dishwasher level. The bracket is made of metal and is approximately 3” in length. The screws are not included with the bracket, they must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the dishwasher before starting the repair.

Dishwasher door seal (dishwasher door gasket)

Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.

Screw

Sold individually.

Hose clamp

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Seal (seal at bottom of the dishwasher door)

This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The door seal is designed to seal the gap between the dishwasher tub and outer edge of the door. This helps to prevent leaks when your dishwasher is running. A leaking dishwasher is a good indication that the door seal is damaged. This seal is sold individually and is an OEM part sourced directly from the manufacturer.

Water inlet valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Seal (cabinet seal between dishwasher and cabinets)

This seal is attached to the inner cabinet to reduce noise.

Drain hose (dishwasher drain hose loop with check valve. Goes from pump to drain hose - 67 inches)

This part is used to drain water from your dishwasher.

Cover screw (screw)

Sold individually.

Door spring (dishwasher door spring)

This dishwasher door spring is sold individually. It is recommended if you are replacing one side, to replace both.

Hose clamp

This single hose clamp is used to hold the water hose in place on the pump, to avoid the hose or pump from leaking water. If you notice your washer leaking you may need to replace the clamp. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.

Inlet fill hose (water fill hose)

This fill hose is a genuine OEM replacement part for your dishwasher. The hose is made of black plastic, and is accordion-style, for ease of movement within your dishwasher. To replace the fill hose, you will need a 1/4 inch nut driver, Channellock pliers, and a Phillips screwdriver. Replacing this part will require some disassembly, such as removing the water inlet valve from the fill hose, and the clamps which secure the hose in place. Reuse your existing clamps when securing your new fill hose in place.

Elbow hose fitting (dishwasher water inlet fitting. Has standard 3/4 inch hose thread on one end and 3/8 inch copper tubing on the other. Copper tubing fitting is compres)

This part has a swivel gooseneck fitting and that allows it to be installed closer to the wall. This part has a 3/4" hose thread on one side and a 3/8" copper tubing on the other side.

Door latch - black (door latch)