66513962K014 Kenmore Dishwasher Parts List

Dishwasher dish rack adjuster kit - left and right side (dishwasher upper dishrack adjuster kit this kit includes both left and right side adjusters and all components needed to service the upper rack roller)

The rack adjuster connects to the dishrack and is used to change the height of the rack. This kit includes the parts to replace the left and right-side rack adjusters and has been upgraded to a more durable metal design. This kit includes 2 adjuster assemblies, 1 left-hand and 1 right-hand actuator cover, 2 gray adjuster covers, and 2 gray adjuster housings. The most common symptoms linked with faulty rack adjusters include: leaking, door latch failure, door not closing, dishes not cleaning properly, and failure to start the washing cycle. It is recommended to replace both the right and left side adjusters at the same time.This is a genuine OEM part.

Door balance link kit (dishwasher door hinge cable and roller kit. Replaces right and left side.)

The door balance kit helps support the weight of the dishwasher door while it opens and closes. If the spring to the door is damaged/broken or the door is not opening and closing properly you will need to replace this part. This door kit includes 2 door balance links and 2 door balance mounts with wheels for the left and right side of the door. This is a genuine OEM part.

Tine pivot (dishwasher tine pivot clip.)

This tine pivot clip helps hold the tine row in place on your dish rack. If your clip is broken or cracked, you should replace it. This clip is made from plastic and is a genuine OEM part. It is sold individually.

Dishwasher dishrack adjuster (upper dishrack tether adjuster strap)

Sold individually. This dishrack adjuster is for dishwashers. Dishrack adjuster lets you change the height of the dishwasher's upper rack. Wear work gloves to protect your hands when installing this part.

Retainer clip - black (access panel retaining clip, black)

This part is used to hold the access panel in place. Sold individually.

Drawer track

This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack will not slide out, or your old drawer track is warped and causes the dish rack wheels to fall off or jam. You will need a flat blade screwdriver to remove the rear stop, so you can pull out the drawer track.

Rubber washer (washer, heater element)

The black heating element washer goes between the heating element and the dishwasher tub to form a seal where the element attaches to prevent water from leaking during its cycle. If the washer goes bad it will cause water to leak out on to the floor. This part is made of rubber, measures approximately 1” in diameter and is sold individually. This is a genuine OEM part.

Spinner kit (upper spray spinner kit)

The water feed tube spinner is also called the 3rd-level spinner. It is located at the top inside the dishwasher tub. This part works like a little spray arm at the top of your dishwasher that distributes water across the top dish rack to help clean the dishes below. If your dishes are not being cleaned properly, or the spray arm is not spraying water, it could be clogged or damaged and will need to be replaced. This spinner is white in color, made of plastic and is a genuine OEM part.

Dishwasher drain pump (dishwasher drain pump. If the dishwasher does not drain then the drain hose could be clogged or the drain pump damaged or defective.)

Screw, 8/18 x 3/8 (screw, 10-24 3/8)

This screw is sold individually.

Tine row - kit of 2 (tine row)

This tine row is for the top rack of your dishwasher, and prevents cups, dishes, and other items from moving around during the cycle. If your current row is missing one or more tines, or the tines have become corroded and are leaving marks on your dishes, you may want to consider replacing it. To do so, simply snap off the tine row pivots that hold the tine row in place, and remove the existing tine row. Then, simply replace it with the new tine row, and snap the tine row pivots back into place. When you order this part, it will come with a set of 2 tine rows. This is an OEM part sourced directly from the manufacturer.

Dishwasher door seal (dishwasher door gasket)

Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.

Retainer clip - white (access panel retaining clip, white)

This part is used to hold the access panel in place. Sold individually.

Screw

Sold individually.

Dishwasher heating element (heating element)

The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.