66513453K902 Kenmore Dishwasher Parts List

Rack track stop (stop)

This gray rack track stop is used for your upper dish rack track to prevent the rack from sliding off the slide rail. If your rack is falling off the track, you may need to replace the track stop. This is a genuine OEM part and is sold individually.

Dishwasher heating element (heater element)

The heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dishes are not drying or the water in the dishwasher is not getting hot you may need to replace the element. This kit includes the heater, two heater fasteners, and is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Mounting bracket

The mounting bracket is used to attach the dishwasher to the underside of the counter. The mounting bracket holds the dishwasher in place to keep it from moving during cycles and to keep the dishwasher level. The bracket is made of metal and is approximately 3” in length. The screws are not included with the bracket, they must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the dishwasher before starting the repair.

Dishwasher door gasket with strike - black (gasket)

This one-piece door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking, tears, or there are gaps in your gasket, you may need to replace the door gasket. This black door gasket is made of rubber, includes a new latch strike plate for the door latch, and is a genuine OEM part.

Dishwasher chopper assembly (chopper assembly)

This part chops up/mince the food particles to prevent from clogging the dishwasher pump. This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.

Rinse-aid dispenser cap (rinse aid cap)

The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leaking detergent, there could be an issue with the rinse aid cap. Check the cap and its gasket for any damage or melting. If the cap has melted or it is not sealing the dispenser properly, the part should be replaced right away. This rinse aid cap comes with the gasket, so you should discard the existing gasket and rinse aid cap at the same time. The repair is relatively straightforward, and requires no tools.

Bi-metal fuse (fuse)

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Also known as Thermal Fuse.

Circulation pump and motor (pump motor assembly)

The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.

Friction sleeve

The friction sleeve helps to reduce friction between the door hinge and the door and to keep your door quiet when it opens and closes. This part is a little over an inch long and is black in color. It is sold individually.

Detergent and rinse aid dispenser (dispenser)

This part releases the detergent and rinse aid into the dishwasher. This detergent dispenser is for dishwashers. Detergent dispenser holds the dishwasher detergent in a covered compartment. Unplug the dishwasher or shut off the house circuit breaker before installing this part. Wear work gloves to protect your hands during this repair.

Rubber washer (heater terminal nut)

The black heating element washer goes between the heating element and the dishwasher tub to form a seal where the element attaches to prevent water from leaking during its cycle. If the washer goes bad it will cause water to leak out on to the floor. This part is made of rubber, measures approximately 1” in diameter and is sold individually. This is a genuine OEM part.

Spinner kit (spinner)

The water feed tube spinner is also called the 3rd-level spinner. It is located at the top inside the dishwasher tub. This part works like a little spray arm at the top of your dishwasher that distributes water across the top dish rack to help clean the dishes below. If your dishes are not being cleaned properly, or the spray arm is not spraying water, it could be clogged or damaged and will need to be replaced. This spinner is white in color, made of plastic and is a genuine OEM part.

Dishwasher drain pump (drain pump)

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Spray arm seal (bearing)

Also known as a wash arm seal.