66513932K014 Kenmore Dishwasher Parts List

Rack stop clip (stop clip)

This rack stop clip works for either the right or left side of your upper dish rack. This part is sold individually.

Tine pivot (dishwasher tine pivot clip.)

This tine pivot clip helps hold the tine row in place on your dish rack. If your clip is broken or cracked, you should replace it. This clip is made from plastic and is a genuine OEM part. It is sold individually.

Drawer track

This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack will not slide out, or your old drawer track is warped and causes the dish rack wheels to fall off or jam. You will need a flat blade screwdriver to remove the rear stop, so you can pull out the drawer track.

Dishwasher upper rack roller (dishrack wheel assembly, fixed 2-position)

This assembly is the wheel and the mount for your upper dishrack. Sold individually. This is an authentic OEM part for use with Whirlpool, KitchenAid, Kenmore and Jenn-Air Dishwashers. The dishrack wheel lets you roll the rack easily on the support rails. This part is sold individually. The most common reason for replacing the dishrack wheel is if it breaks causing the rack to jam. The tool that you will need to replace the dishrack wheel is a flathead screwdriver.

Spinner kit (upper spray spinner kit)

The water feed tube spinner is also called the 3rd-level spinner. It is located at the top inside the dishwasher tub. This part works like a little spray arm at the top of your dishwasher that distributes water across the top dish rack to help clean the dishes below. If your dishes are not being cleaned properly, or the spray arm is not spraying water, it could be clogged or damaged and will need to be replaced. This spinner is white in color, made of plastic and is a genuine OEM part.

Tine row - kit of 2 (tine row)

This tine row is for the top rack of your dishwasher, and prevents cups, dishes, and other items from moving around during the cycle. If your current row is missing one or more tines, or the tines have become corroded and are leaving marks on your dishes, you may want to consider replacing it. To do so, simply snap off the tine row pivots that hold the tine row in place, and remove the existing tine row. Then, simply replace it with the new tine row, and snap the tine row pivots back into place. When you order this part, it will come with a set of 2 tine rows. This is an OEM part sourced directly from the manufacturer.

Screw

Sold individually.

Upper dishrack (dishrack)

Rack only.

Door latch - black (door latch *part has been redesigned by the manufacture)

NOTE: This part has been redesigned, it may appear different but will still function the same as the original.

Thermal fuse (thermal cut out fuse kit)

This is a replacement thermal fuse for your dishwasher. The thermal fuse is sometimes known as the thermal cutoff. The thermal fuse shuts off the dishwasher if the dishwasher shorts out or overheats. If your dishwasher is cutting out during the cycle, or will not start, you may have an issue with your thermal fuse. If your dishwasher control panel does not light up, the first thing you should check is the fuse. Before you begin to repair this part, be sure to disconnect the dishwasher from the power source, as you will be working around electricity.

Clip (dispenser door rack guard)

This OEM dishrack guard clip fits on the front of the upper dishrack and acts as a bumper between the rack and inner door panel. This guard clip is approximately 3 inches long and made of plastic. To replace this part, open the dishwasher door and then slide the upper dishrack out, then simply unclip the faulty guard clip before fastening the new one.

Dishwasher electronic control board (control board)

Positioner

Dishwasher wire harness (wire)

This wire harness is for dishwashers and supplies power to electrical components in the dishwasher.

Dishwasher water feed tube (upper wash water supply tube)

The water feed tube carries water to the upper spray components.