6651590840 Kenmore Dishwasher Parts List

Rubber washer (washer, rubber (2))

The black heating element washer goes between the heating element and the dishwasher tub to form a seal where the element attaches to prevent water from leaking during its cycle. If the washer goes bad it will cause water to leak out on to the floor. This part is made of rubber, measures approximately 1” in diameter and is sold individually. This is a genuine OEM part.

Screw, 8/18 x 3/8 (screw, 8a x 3/8 hex wshr. Hd. Tapping (2))

This screw is sold individually.

Drain and wash impeller kit (impeller, wash (includes illus. 12 & 13))

This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper and installation screw. This part helps stop your dishwasher from leaking and helps with the proper draining of the dishwasher.

Spring, lid

The lid spring helps open the detergent dispenser cover, which is located on the inside of the door panel, when it reaches the cycle to dispense soap into the dishwasher. If the lid will not open or the detergent is not dispensing, you may need to replace the lid spring. This is a genuine OEM part.

Lower dishrack kit (dishrack, lower (includes illus 4))

The lower rack provides easy loading with flexibility for small and large items, and helps hold the dishes in place during the wash and dry cycle. The rack measures approximately 22-inch x 21-inch. The rack is light gray in color with wheels included, lower fold down, and a flexrow retainer. This is a genuine OEM part.

Hose clamp (clamp, hose)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Screw - 8-18 x 1/2 (screw, 8-18 x 1/2 phlps. Hex. Wash. Hd. Tapping ground)

Sold Individually.

Detergent dispenser cover kit (lid, detergent dispenser)

This kit also includes the lid hinge pin, spring, snap and latch.

Screw (screw, 8-18 x 1/2 phlps. Pan hd. W/washer tapping)

Metallic screw that is less than an inch long. Does not include the plastic washer.

Cover screw (screw, 10-16 x 1/2 phlps. Truss hd. Thread forming (2))

Sold individually.

Tandem rack rollers - set of 4 (wheel & shroud assembly (4))

Each tandem roller holds two wheels. There are four sets of tandem rollers in this roller kit, so you will be getting eight wheels in all. They are all white, and are meant for use on the lower rack of your dishwasher.

Dishrack (dishrack (upper))

Screw - 8-18 x 5/8 (screw, 8-18 x 5/8 phlps. Pan hd. Hi-lo st. Stl. (8))

Sold individually.

Drain check valve with o-ring (valve, check (includes illus. 21 & 23))

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Pump outlet seal (seal, pump outlet)

This part is the replacement pump outlet seal or seal ring for your dishwasher. It is made of black rubber and is sold individually. The seal ring creates a seal between the upper compartment of the pump to the pump body. If the seal ring fails, you won’t have good water pressure, and therefore your dishes won’t come clean properly. Improperly cleaned dishes are a good indicator of a bad seal ring. Be sure to disconnect your dishwasher to the water and power sources before you begin this repair. This is an OEM part sourced directly from the manufacturer.