6654493390 Kenmore Wall Oven Parts List

Light bulb - 40w (bulb, oven light)

This 40-watt light bulb has a standard screw-in base. It is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Bake element - 2600w 240v (unit, bake)

The 2600 watt 240 volts bake element is located inside the oven on the bottom to supply heat while baking. This closed hinged style bake element is 15 3/4-inch long 16 5/8-inch wide, terminal depth is 3-inch and they are 1 3/4 inches apart. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Light bulb - 120v 25w (lamp, oven see note 1)

This 25-watt, 120-volt light bulb is 2.5 inches long. It has a small, screw-in base and it is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Screw (screw see note 1)

This screw is half an inch long. It is made of metal and is intended for use with ranges, refrigerators, and washing machines.

Broil element - 240v (unit, broil)

If your broil element is no longer heating or it has shorted out, you may need to replace it. You can use a multimeter to test the broil element for continuity. The three loop broil element is located on the roof of the oven cavity to supply heat for broiling. The element has push-on terminals and measures 12-inch wide and 19-inch long. This is a genuine OEM part. Please remember to disconnect the power to the oven before starting your repair.

Screw (screw, 8-18 x 1/2 (8))

Metallic screw that is less than an inch long. Does not include the plastic washer.

Cover screw (screw (3))

Sold individually.

2 piece broiler pan (pan, broiler)

The broiler pan and insert allows you to cook on a stable surface while allowing the liquid to drain into the pan below, making clean up easier. The measurements for the pan set are 1-1/2-inch x 12-3/4-inch x 16-3/4-inch and is a genuine OEM part.

Oven rack (rack, oven)

Sold individually. 21-7/8" wide and 16" deep.

Inner door glass (glass, inside/outside)

Frame is no longer available.

Light gasket (gasket, light)

This part creates a seal around the light lens and bulb.

Sockt-lite (oven light assy.)

The oven light socket assembly with lens provides power to the light bulb while holding the bulb in place. If the light socket shorted out and the oven light is no longer coming on, you may need to replace the light socket. This part measures approximately 4.25” L x 3” w. This is the socket and lens only; light bulb is not included must be ordered separately. This is a genuine OEM part. Please make sure to disconnect the power to the oven before starting the repair.

Door interlock switch kit (secondary switch see note 1)

The door interlock switch kit contains 2 switches - 15 Amp - 125/250 Volt with 3/16-inch terminals. The switches are used to sense when the microwave door is open or closed. If your microwave will not start, or will not turn on, you may need to replace these switches. This is a genuine OEM kit. Please remember to disconnect the power to your microwave before starting the repair. PLEASE NOTE: The door interlock switch kit includes 2 single pole, double throw (SPDT) micro switches. As per the manufacture for the secondary interlock switch order part # 56001100.

Oven door spring (spring, oven door (2))

Temperature sensor (sensor, heat)

The genuine OEM temperature sensor is used in self-cleaning ovens to detect the temperature within the oven cavity. Its 1000 ohm resistance increases with temperature. This sensor is 6 inches in length, has male leads, and comes with ceramic wire nuts. If your oven is too hot, not heating evenly, or has little to no heat when baking, you may need to replace the temperature sensor. Please make sure to disconnect the power to your range before starting your repair.