79097503000 Kenmore Range Parts List

Radiant element with limiter - 1200w (range/stove radiant surface element for 6-inch burner. 1200 watts. If the surface element is not heating, use a multimeter to test the element for con)

The 6” radiant cooking element with limiter fits under the glass cooktop and supplies heat to the cooking area. If your element is not heating, you can test the element for continuity with a multimeter. If the element doesn’t have continuity you will need to replace the element. If it doesn’t have continuity it is suggested to check the element switch because it could be defective and need to be replaced. This element is 1200 watts and is a genuine OEM part. The manufacturer suggests making sure the cooking element is cooled before starting the repair. Please remember to disconnect the power to the appliance before starting the repair.

Lens (light lens)

This is an oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover protects the light bulb from being damaged. The main reason to replace the light lens cover is if it is cracked, damaged, or missing. Make sure the lens cover is cool to the touch before you begin this repair. To remove the lens cover, simply turn it counter clockwise until you can remove it. Replace it with a new cover and turn it clockwise to lock it into place. This is an OEM part sourced from the manufacturer, and it is sold individually.

Glass (oven door glass.)

This tempered glass is supplied by the original manufacturer and measures 20 inches by 13 inches. It is an inner door glass, designed for use in ranges/ovens and has several purposes which include providing heat insulation, acting as protective barrier, and providing an opening to monitor the cooking/heating process. Over time the glass can break or break from impact, thermal shock, or improper installation. If the glass is defective, it needs to be replaced promptly to avoid leaking, loss of insulation and potential harm to the user. Remove any fasteners or clips that secure the glass and carefully dispose of it. Position the new glass in the same position and secure it appropriately.

Main terminal block kit (terminal block kit for electric range and dryer power cords.)

This terminal block kit (also called terminal boards or strips) provides a convenient means of connecting individual electrical wires. This kit includes mounting screws and hex nuts and can be used with dryers and ranges. This kit allows you to attach the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Probe (oven temperature sensor)

The temperature sensor, also known as an oven probe, helps measure the temperature within the oven cavity. If your oven is too hot, not heating evenly, has little to no heat when baking, or flashing F3/F4 error messages on your control board, you may need to replace this part. This part measures 6" long and is made of metal. Please make sure to disconnect the power to your oven range before starting this repair. This temperature sensor is a genuine OEM part.

Broiler pan grate insert (insert, broiler pan)

The broiler pan and insert allows you to cook on a stable surface while allowing the liquid to drain into the pan below, making clean-up easier. This is a genuine OEM part.

Oven light socket

The light socket is located inside the oven cavity to provide power to the light while holding the light bulb in place. If the light bulb is not working, the switch might have failed and will need to be replaced. This is a genuine OEM part. Please remember to disconnect power to the oven before starting your repair.

Inner glass (oven door glass)

Door spacer (oven door spacer)

Bake element (hidden bake element)

Levelling leg with rubber pad (leveling leg with pad)

Sold Individually.

Oven door light switch (oven door/light switch, 4 terminal double contact)

The oven door light switch is a on an off mechanism that will shut the oven light off when the door is closed or turn on when the door is open. When you open the oven door and the light does not come on, it could be the switch or the light bulb and one of them will need to be replaced. The light switch is black in color, 4 terminal double contact, and measures approximately 2 1/2” in length. Please remember to disconnect the power to the oven before starting the repair. This oven door light switch is a genuine OEM part.

Radiant burner element - 9 inch 3200w (9 inch, 3200 watt top radiant heating element)

Convection fan blade

The convection fan blade works in conjunction with the convection fan motor by turning to circulate the hot air through the oven for even heating. The fan blade attaches to the convection motor shaft and is secured by the blade nut. If the part is damaged or worn you will need to replace it. This part is made from metal and measures approximately 5” in diameter. Please remember to disconnect the power to the oven before starting your repair. This is a genuine OEM part and is sold individually.

2 pack light bulb - 40w