79061131100 Kenmore Range Parts List

Drip bowl - 8" (pan)

The eight-inch drip bowl sits under the surface burner element to collect anything that may drip or spill over, to make cleaning up quick. This bowl measures approximately 10-inch in diameter at its widest point at the top. If your drip bowl becomes damaged or rusted it is best to replace the drip bowl to avoid any grease or spills from dripping down inside the range. This chrome drip bowl is compatible with most electric ranges that utilize plug-in surface burners. This is a genuine OEM part and is sold individually.

Rear drawer glide (glide)

This rear drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact. If you are having trouble opening/closing the broiler drawer, the glide may be broken and will need to be replaced. This is a genuine OEM part and is sold individually.

Front drawer glide (glide)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Terminal block kit (terminal block)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Surface element - 8 inch - 2600w (8-inch 2100-watt surface element)

This surface burner element is eight inches in diameter. It has five turns, 2600 watts and looped terminal ends. The element provides heat to the cooking surface on your range. If your element is not heating, you may need to replace this part. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part. It is sold individually.

6-inch coil burner element (element)

This 6-inch element has looped terminal ends, 1250 watt, four turn and comes with a black medallion center. The element provides heat to the cooking surface on your range. If your element is not heating, you may need to replace the element. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part and is sold individually.

Oven rack

The metal chrome oven rack is a genuine OEM part. The oven rack is located inside of the oven cavity to provide a stable surface for cooking or broiling. This rack measures approximately 23” long x 16” wide and is sold individually. If your rack is rusted, damaged or missing you will need to replace the oven rack. No tools are required for this repair.

Infinite burner switch - small element - 240v (infinite switch)

This surface burner switch controls the temperature of the stove top 6-inch surface burner. This switch is 240-volt, 1250-1500 watt, and 5.2-6.25 amp. If your element will not heat and is not defective, then you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Indicator light lens (lens kit)

Bake element - 240v (element)

This bake element is found on the bottom of the oven.

Main terminal block kit (block)

This terminal block kit (also called terminal boards or strips) provides a convenient means of connecting individual electrical wires. This kit includes mounting screws and hex nuts and can be used with dryers and ranges. This kit allows you to attach the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Steel washer (washer)

This washer works in conjunction with the oven door handle to secure the oven door together. The washer measures 3/4-inch x 1/4-inch, is made of metal and is sold individually. This is a genuine OEM part.

Leveling leg (level leg)

Anti-tip kit (anti tip kit)

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.

Oven door seal with clips (oven door seal)

Also known as gasket.