79064090302 Kenmore Range Parts List

Oven bake element (bake element)

The bake element is located on the bottom of the oven cavity to supply heat for baking. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Drip bowl - 8" (pan)

The eight-inch drip bowl sits under the surface burner element to collect anything that may drip or spill over, to make cleaning up quick. This bowl measures approximately 10-inch in diameter at its widest point at the top. If your drip bowl becomes damaged or rusted it is best to replace the drip bowl to avoid any grease or spills from dripping down inside the range. This chrome drip bowl is compatible with most electric ranges that utilize plug-in surface burners. This is a genuine OEM part and is sold individually.

Rear drawer glide (glide)

This rear drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact. If you are having trouble opening/closing the broiler drawer, the glide may be broken and will need to be replaced. This is a genuine OEM part and is sold individually.

Terminal block kit (terminal block)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Surface element - 8 inch - 220v (element)

The coil burner element is eight inches in diameter. It has four turns, 220 volts and looped terminal ends. The coil burner element provides heat to the cooking surface on your range. You might need to replace this part if your element is not heating. It might have shorted out around the coil or the terminal block; you can test the coil to see if the burner or the switch may be at fault. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part and is sold individually.

Surface element - 6 inch (element)

The standard Y-frame 6” surface element supplies heat to the cooking surface on your range and is a genuine OEM part. It has a black center medallion and looped terminal end. If your element is not heating, shorted out around the coil or if the terminal block shorted out and burnt out the contacts on the end, you may need to replace the element. Please be sure to disconnect the power to your range before starting your repair. Note: The manufacturer suggests replacing the receptacle at the same time.

Drip bowl - 6 inch (pan)

This six-inch drip bowl or drip pan is found underneath the small surface element on your cooktop or range. A similar eight-inch drip bowl also exists, so be sure to check which size you need. The drip bowl is designed to catch any spills when cooking on your range. If your old drip bowl is stained or rusted, you may need to replace it. The drip bowl is easy to repair, it should simply fit into place.

Light bulb (bulb)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Oven rack

The metal chrome oven rack is a genuine OEM part. The oven rack is located inside of the oven cavity to provide a stable surface for cooking or broiling. This rack measures approximately 23” long x 16” wide and is sold individually. If your rack is rusted, damaged or missing you will need to replace the oven rack. No tools are required for this repair.

Burner switch kit (universal in)

This burner switch controls the stove top surface burner temperature. If your element will not heat and does not look defective, you may need to replace the switch. This kit includes screws, keeper for mounting, and several insert sizes to match your old knob. This switch kit is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Indicator light lens (lens kit)

Steel washer (washer)

This washer works in conjunction with the oven door handle to secure the oven door together. The washer measures 3/4-inch x 1/4-inch, is made of metal and is sold individually. This is a genuine OEM part.

Leveling leg (level leg)

Oven door seal with clips (oven door seal)

Also known as gasket.

Handle

his oven door handle is for ranges. Wear work gloves to protect your hands when installing this part.