79090312010 Kenmore Range Parts List

Terminal block kit (terminal block)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Infinite burner switch (infinite large element switch)

This surface burner switch controls the stove top 8-inch surface burner temperature. This switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp. If your element is not defective but will not heat, you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Surface element - 8 inch - 2600w (8-inch 2100-watt surface element)

This surface burner element is eight inches in diameter. It has five turns, 2600 watts and looped terminal ends. The element provides heat to the cooking surface on your range. If your element is not heating, you may need to replace this part. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part. It is sold individually.

6-inch coil burner element (element)

This 6-inch element has looped terminal ends, 1250 watt, four turn and comes with a black medallion center. The element provides heat to the cooking surface on your range. If your element is not heating, you may need to replace the element. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part and is sold individually.

Light bulb (lamp)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Temperature sensor (probe)

This temperature sensor detects the temperature within the oven cavity.

Infinite burner switch - small element - 240v (infinite switch)

This surface burner switch controls the temperature of the stove top 6-inch surface burner. This switch is 240-volt, 1250-1500 watt, and 5.2-6.25 amp. If your element will not heat and is not defective, then you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Bottom panel (panel)

This is used as the "floor" of the oven cabinet. Note: Does not come with rivets or screws. Must be purchased locally.

Lens

This is an oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover protects the light bulb from being damaged. The main reason to replace the light lens cover is if it is cracked, damaged, or missing. Make sure the lens cover is cool to the touch before you begin this repair. To remove the lens cover, simply turn it counter clockwise until you can remove it. Replace it with a new cover and turn it clockwise to lock it into place. This is an OEM part sourced from the manufacturer, and it is sold individually.

Glass

This tempered glass is supplied by the original manufacturer and measures 20 inches by 13 inches. It is an inner door glass, designed for use in ranges/ovens and has several purposes which include providing heat insulation, acting as protective barrier, and providing an opening to monitor the cooking/heating process. Over time the glass can break or break from impact, thermal shock, or improper installation. If the glass is defective, it needs to be replaced promptly to avoid leaking, loss of insulation and potential harm to the user. Remove any fasteners or clips that secure the glass and carefully dispose of it. Position the new glass in the same position and secure it appropriately.

Broil element (broiler element)

This broil element is found on the roof of the oven.

Drawer glide (rear door glide)

Sold Individually.

Light lens indicator (lamp lens)

Oven door cap - white (door trim)

This part goes over the top of the oven door glass. The door handle also attaches to the door cap.

Anti-tip kit (anti tip kit)

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.