79091419010 Kenmore Range Parts List

Rear drawer glide (glide)

This rear drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact. If you are having trouble opening/closing the broiler drawer, the glide may be broken and will need to be replaced. This is a genuine OEM part and is sold individually.

Front drawer glide (glide)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Light bulb (lamp)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Oven rack

The metal chrome oven rack is a genuine OEM part. The oven rack is located inside of the oven cavity to provide a stable surface for cooking or broiling. This rack measures approximately 23” long x 16” wide and is sold individually. If your rack is rusted, damaged or missing you will need to replace the oven rack. No tools are required for this repair.

Infinite burner switch - small element - 240v (infinite switch)

This surface burner switch controls the temperature of the stove top 6-inch surface burner. This switch is 240-volt, 1250-1500 watt, and 5.2-6.25 amp. If your element will not heat and is not defective, then you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Dual element with limiter (element)

Dual Element with Limiter -9 Inch /6 Inch - 1300W 1200W. With this element, you can adjust the size of the burner you want to use to match your pots/pans.

Radiant element with limiter - 1200w (element)

The 6” radiant cooking element with limiter fits under the glass cooktop and supplies heat to the cooking area. If your element is not heating, you can test the element for continuity with a multimeter. If the element doesn’t have continuity you will need to replace the element. If it doesn’t have continuity it is suggested to check the element switch because it could be defective and need to be replaced. This element is 1200 watts and is a genuine OEM part. The manufacturer suggests making sure the cooking element is cooled before starting the repair. Please remember to disconnect the power to the appliance before starting the repair.

Probe

Note: Connector could be different than original. If so cut & splice wires together with porcelain wire nuts.

Bake element - 240v (element)

This bake element is found on the bottom of the oven.

Light lens indicator (lamp lens)

Anti-tip kit (anti tip kit)

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.

Leveling leg assy (level)

The front leveling leg is used to support and level your range. The leveling leg allows you to adjust the height of your range to make the range level. This part is just the leg, the hardware is not included and can be ordered separately. If the leveling leg breaks or can no longer be adjusted, you will need to replace it. This is a genuine OEM part and is sold individually.

Wafer head screw (screw)

Oven door seal with clips (oven door seal)

Also known as gasket.

Dual surface element switch (switch)

This switch controls the stove top surface burner. This surface element control switch is for ranges. Surface element control switch turns the surface element on and off and controls how much heat the element produces. Unplug the range or shut off the house circuit breaker for the range before installing this part.