79092802011 Kenmore Range Parts List

Light bulb (lamp)

This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Temperature sensor (probe)

This temperature sensor detects the temperature within the oven cavity.

Infinite burner switch - small element - 240v (infinite switch)

This surface burner switch controls the temperature of the stove top 6-inch surface burner. This switch is 240-volt, 1250-1500 watt, and 5.2-6.25 amp. If your element will not heat and is not defective, then you may need to replace the switch. This burner switch is a genuine OEM part. It is recommended to disconnect the power to your range before you start your repair.

Radiant element with limiter - 1200w (element)

The 6” radiant cooking element with limiter fits under the glass cooktop and supplies heat to the cooking area. If your element is not heating, you can test the element for continuity with a multimeter. If the element doesn’t have continuity you will need to replace the element. If it doesn’t have continuity it is suggested to check the element switch because it could be defective and need to be replaced. This element is 1200 watts and is a genuine OEM part. The manufacturer suggests making sure the cooking element is cooled before starting the repair. Please remember to disconnect the power to the appliance before starting the repair.

Oven rack (rack)

This is a replacement rack for your oven. The oven rack fits into grooves on the side of the oven wall, and acts as a shelf that you can place food items on when you want to cook them in the oven. This rack is 24 inches wide and 16 inches long, and is chrome in color. Occasionally, the rack will become warped or distressed, or it may be missing from your oven. In these cases, it will need to be replaced. To replace the rack, simply slide out the old rack and replace it with the new one.

Lens

This is an oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover protects the light bulb from being damaged. The main reason to replace the light lens cover is if it is cracked, damaged, or missing. Make sure the lens cover is cool to the touch before you begin this repair. To remove the lens cover, simply turn it counter clockwise until you can remove it. Replace it with a new cover and turn it clockwise to lock it into place. This is an OEM part sourced from the manufacturer, and it is sold individually.

Broil element (broiler element)

This broil element is found on the roof of the oven.

Drawer glide (rear door glide)

Sold Individually.

Light lens indicator (lamp lens)

Oven door cap - white (door trim)

This part goes over the top of the oven door glass. The door handle also attaches to the door cap.

Bottom panel (panel)

Anti-tip kit (anti tip kit)

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.

Leveling leg assy (level)

The front leveling leg is used to support and level your range. The leveling leg allows you to adjust the height of your range to make the range level. This part is just the leg, the hardware is not included and can be ordered separately. If the leveling leg breaks or can no longer be adjusted, you will need to replace it. This is a genuine OEM part and is sold individually.

Dual surface element switch (switch)

This switch controls the stove top surface burner. This surface element control switch is for ranges. Surface element control switch turns the surface element on and off and controls how much heat the element produces. Unplug the range or shut off the house circuit breaker for the range before installing this part.

Screw (screw-8-18x1)

Sold Individually.