79571033010 Kenmore Freezer Parts List

Handle screw (handle stopper)

This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as they commonly wear at the same rate. This is about 1 inch long and metallic in color.

Plate assembly,front (door mullion - grey)

This is a replacement mullion rail for your French door-style refrigerator. You will typically find the mullion rail on the left side refrigerator door. The mullion rail helps to keep the refrigerator door closed. If the door will not close properly or if you notice leaking on your floor, you may need to replace the door mullion. A faulty mullion can gather moisture, resulting in a leak. To replace the mullion, simply disconnect the old mullion from the wire harness and unscrew it. Re-attach the wire harness to the mullion and screw it back into place.

Refrigerator door switch

The light switch lights up the interior cabinet of the refrigerator or freezer when the door is opened. If you open the door and the light won’t come on, or the light is always on, you may need to replace the light switch. The switch is white in color and measures approximately 2 1/2”. This is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Plastic tube - 5/16 inch (tube)

The 5/16” plastic water tubing attaches to the water inlet valve and goes into the refrigerator. The tubing supplies water to the water dispenser and the ice maker. If the tubing becomes damaged or cracked, it can cause water to leak out onto the floor and the water tubing will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power and water supply before starting the repair.

Refrigerator water filter

This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.

Water inlet valve assembly (valve asy,wa)

This includes the primary and secondary valves along with the wire harness.

Roller assembly

Plastic tube

This part is the replacement water line or tube for your refrigerator. It is made of white plastic and is sold individually. This tube supplies water to the ice maker and water dispenser If your refrigerator is leaking, or it will not dispense water or ice, you may have a damaged water line. When you replace the water line, you may want to pick up a new water tube union as well. You can use a utility knife to cut the old water line where it is damaged and use the union to attach the new water line to the old one. This tubing is an OEM part from the manufacturer.

Door holder

This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.

Evaporator fan motor (motor)

This 13-volt evaporator fan motor helps circulate air over the refrigerator coils. These coils will then convert the heat into cool air, which is then circulated from the freezer section to the fresh food section. If the fresh food section is too warm or the motor has failed, you will need to replace the evaporator fan motor. It is suggested to replace the thermistor when replacing the evaporator fan. The fan motor is in the freezer section of the refrigerator, and includes the harness and plug. Please remember to disconnect the power to the refrigerator before starting your repair. This is a genuine OEM part.

Spring,lever (spring lever)

Elbow (connector)

Refrigerator water reservoir (tank asy,wat)

The water reservoir holds the water for the water dispenser as the water chills.

Switch,push button

Ice maker assembly kit (icemaker)

This is an ice maker assembly kit designed for use within LG refrigerator-freezers. Ice makers are made to pull water from the water line, freeze it, and then store it in the form of cubes to be dispensed or crushed, depending on your preference and the model of the refrigerator. This assembly comes with the entire ice-making assembly, not the portion that stores and dispenses the ice cubes from the dispenser. If your current ice maker is simply not making enough ice or any at all, or is broken or damaged in any way, it must be replaced. This ice maker assembly is made entirely of durable white plastic and connects via its single wire harness and features an on/off switch that needs to be turned on for it to function. This assembly is sold individually and does not come with any other ice maker parts.