79571069011 Kenmore Refrigerator Parts List

Handle screw (door handle mounting post)

This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as they commonly wear at the same rate. This is about 1 inch long and metallic in color.

Mullion spring (mullion spring for refrigerator door guide.)

This spring is located on the mullion, or door flap, of your fridge. This spring is sourced from the genuine OEM manufacturer for various refrigerator models. It measures about 1.5 inches in total length, and is made entirely out of metal.

Refrigerator door switch (refrigerator door or freezer drawer switch)

The light switch lights up the interior cabinet of the refrigerator or freezer when the door is opened. If you open the door and the light won’t come on, or the light is always on, you may need to replace the light switch. The switch is white in color and measures approximately 2 1/2”. This is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Refrigerator water filter (LG replacement water filter reduces contaminants in household water including lead, mercury, and chlorine. Replace filter every 6 months or 200 gallon)

This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.

Plastic tube - 5/16 inch (tube,plastic)

The 5/16” plastic water tubing attaches to the water inlet valve and goes into the refrigerator. The tubing supplies water to the water dispenser and the ice maker. If the tubing becomes damaged or cracked, it can cause water to leak out onto the floor and the water tubing will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power and water supply before starting the repair.

Bottom door bin (door shelf bin)

The door bin is attached to the inside of the refrigerator door, and typically holds condiments, jars, and bottles. This OEM basket assembly is made of white and clear plastic. Measures approximately 16 inches long x 4 1/2 inches high x 5 inches deep. These parts should fit tightly to the door of your refrigerator, if yours is loose you should replace it immediately, as it could result in its contents spilling into the inside of your refrigerator, or onto the floor.

Door shelf bin (door basket assembly)

This door bin is made of white plastic, attaches to the inside of the refrigerator door, and typically holds condiments, jars, and bottles. This door basket measures approximately 14 inches wide x 11 inches high x 4 inches deep. To replace your faulty or damaged basket, simply remove it from the door, and slide the new one in place.

Ice maker assembly - 6 wire (refrigerator icemaker assembly. Per the manufacturer this part is correct if the original icemaker has a smaller white wire connector with 6 wires in)

NOTE: As per manufacture the secondary (smaller) wire connector has 6 wires in it. If original ice maker has 3 wire connector see part number PS7788172. Please verify connector before ordering.

Water inlet valve assembly (wire harness for water valve)

This includes the primary and secondary valves along with the wire harness.

Glass shelf

This is the replacement shelf glass for your refrigerator. It is made of glass and is approximately 31 inches wide and 16 inches long. The shelf glass for your refrigerator slides over the crisper cover and acts as a sort of lid. It also creates a shelf that you can place food and beverages on. If your current shelf insert glass is broken, this part is the appropriate replacement. Many of our customers have described this repair as easy. To complete the repair, carefully remove the old glass from the frame and replace it with the new pane of glass. This part is sold individually and is an authentic OEM part.

Door holder

This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.

Push button switch (switch,push button)

This is a genuine replacement switch. It is a push button style switch that is designed for use in your refrigerator. When the door of your appliance is opened the switch is released, and the light comes on. When you close the door the switch is pressed in, and the light turns off. You may need a putty knife to remove your old switch.

Left side connector rail (rail connector)

Spring,lever (lever spring)

Refrigerator door bin assembly (door shelf bin)