Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

79640021900 Kenmore Washer Parts List

1-15 of 92

Washing machine drain pump and motor assembly (pump motor assembly)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Easy Part #:

EAP3579318

Availability:

In Stock

Price:

$50.61

Water inlet valve - hot (valve)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:

EAP3527427

Availability:

In Stock

Price:

$19.18

Water inlet valve - cold (valve)

This valve is used for cold water, bleach dispenser, and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left. The water inlet valve opens to allow the water to enter the washing machine. If your washer will not fill with water, is leaking, or will not stop filling with water, you may need to replace the valve. Please remember to disconnect the power to your washer, remove the fill hoses on the back and pull out the washer to have access to the back before you start your repair. This valve is a genuine OEM part.

Easy Part #:

EAP11728995

Availability:

In Stock

Price:

$49.27

Easy Part #:

EAP3533609

Availability:

In Stock

Price:

$55.61

Detergent dispenser (box)

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.

Easy Part #:

EAP3522644

Availability:

In Stock

Price:

$24.03

Shock absorber kit (shock assembly)

This kit includes 1 shock absorber and 2 mounting pins.

Easy Part #:

EAP3522315

Availability:

In Stock

Price:

$35.62

Spider

The spider, or rear tub support, is located behind the outer tub of your washer, and provides support to the outer tub. It has 3 legs and each measures approximately 10 inches long. If your washer moves or shakes, or sounds noisier than usual during the washing cycle, the support spider may be faulty or broken and should be replaced immediately.

Easy Part #:

EAP3522973

Availability:

No Longer Available

Gasket (seal)

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.

Easy Part #:

EAP3522854

Availability:

In Stock

Price:

$19.60

Ball bearing (b bearing)

This bearing, or ball, is a genuine OEM replacement part for your washer. The bearing allows the tub to rotate smoothly. Replacing this part can be helpful if your washer is extremely loud, or vibrates excessively. Sometimes the seal can fail, allowing water to leak into the bearings. Often you will need to replace the inner and outer bearings, as well as the seal, at the same time.

Easy Part #:

EAP12072605

Availability:

In Stock

Price:

$35.25

Locking pin (hinge)

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Easy Part #:

EAP3523451

Availability:

In Stock

Price:

$9.59

Easy Part #:

EAP3522860

Availability:

In Stock

Price:

$16.11

Clamp assembly (clamp)

The door boot seal clamp, also referred to as an outer door gasket clamp, holds the door boot in place in a front-loading washer. If your washer is leaking from the door and there are no signs of damage to the door boot seal, check to ensure that it is securely fastened. If your boot seal clamp is faulty, or damaged, it should be replaced immediately.

Easy Part #:

EAP3517812

Availability:

In Stock

Price:

$11.62

Cap,drain hose (hose cap)

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

Easy Part #:

EAP3635866

Availability:

In Stock

Price:

$5.45

Pump filter (bag)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Easy Part #:

EAP3522306

Availability:

In Stock

Price:

$23.84

Easy Part #:

EAP3527325

Availability:

In Stock

Price:

$26.29

1-15 of 92