Hello!

You're visiting the Easy Appliance Parts site in U.S.

Would you like to shop on the Canadian site?

Stay on this site
Go to Canadian site

79641722010 Kenmore Washer Parts List

1-15 of 124

Washing machine drain pump and motor assembly (pump motor assembly)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Easy Part #:

EAP3579318

Availability:

In Stock - Ships Today

Price:

$50.61

Water inlet valve - hot (valve)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:

EAP3527427

Availability:

In Stock - Ships Today

Price:

$19.18

Magnetic door plunger (holder)

The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will prevent mold and mildew buildup around your door and seal. If your washer door will not close you many need to replace this part. The magnetic door plunger is a genuine OEM part.

Easy Part #:

EAP3618292

Availability:

In Stock - Ships Today

Price:

$18.02

Bearing,ball (tub bearing)

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

Easy Part #:

EAP7785069

Availability:

In Stock - Ships Today

Price:

$41.28

Gasket (seal)

The outer tub gasket is used to create a seal between the front and rear outer tub to prevent water leaking. The tub gasket is located between the front outer tub and the rear outer tub. If your washer starts leaking from between the outer and rear tub, the tub gasket could be worn out or damaged and will need to be replaced. This part is black in color and made of rubber. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting the repair.

Easy Part #:

EAP3522859

Availability:

In Stock - Ships Today

Price:

$24.03

Easy Part #:

EAP3533609

Availability:

In Stock - Ships Today

Price:

$55.61

Detergent dispenser (box)

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.

Easy Part #:

EAP3522644

Availability:

In Stock - Ships Today

Price:

$24.03

Rotor position sensor assembly (sensor assembly)

The motor rotor position sensor monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer is displaying an LE error code on your control display, the sensor has failed and will need to be replaced. This is a genuine OEM part sourced directly from the manufacturer. Please remember to disconnect the power to your washer before starting your repair.

Easy Part #:

EAP3529186

Availability:

On Order

Price:

$29.33

Tub-to-pump drain hose (tub-to-pump hose)

This hose has bellows to allow for flexibility during the wash and spin cycles.

Easy Part #:

EAP3523345

Availability:

In Stock - Ships Today

Price:

$34.71

Shock absorber kit (shock assembly)

This kit includes 1 shock absorber and 2 mounting pins.

Easy Part #:

EAP3522315

Availability:

In Stock - Ships Today

Price:

$35.62

Motor assembly,ac,pump (recirculation pump motor assembly)

The circulation pump is used in both washers and dishwashers. In the washer, the pump is used to circulate the water during operation. In the dishwasher, the pump is used to drain the water from the dishwasher. If the circulation pump stops working, it will prevent the washer and dishwasher from working properly and will need to be replaced. This circulation pump is 120 volts, 60Hz and 30 watt and a genuine OEM part. Please remember to disconnect the power and water supply before starting your repair.

Easy Part #:

EAP16223509

Availability:

In Stock - Ships Today

Price:

$60.52

Washer hose with bellows (bellows)

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

Easy Part #:

EAP3523347

Availability:

In Stock - Ships Today

Price:

$27.38

Locking pin (hinge)

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Easy Part #:

EAP3523451

Availability:

In Stock - Ships Today

Price:

$9.59

Easy Part #:

EAP3524578

Availability:

In Stock - Ships Today

Price:

$25.53

Easy Part #:

EAP3522806

Availability:

In Stock - Ships Today

Price:

$12.47

1-15 of 124