79648852800 Kenmore Washer Parts List

Washing machine drain pump (pump motor)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Water inlet valve - hot (valve)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Door lock assembly (locker switc)

Shock absorber kit (shock assembly)

This kit includes 1 shock absorber and 2 pins.

Spider

The spider, or rear tub support, is located behind the outer tub of your washer, and provides support to the outer tub. It has 3 legs and each measures approximately 10 inches long. If your washer moves or shakes, or sounds noisier than usual during the washing cycle, the support spider may be faulty or broken and should be replaced immediately.

Gasket (seal)

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.

Locking pin (hinge)

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Bearing,ball (b bearing)

Gasket (seal)

Clamp assembly

The door boot seal clamp, also referred to as an outer door gasket clamp, holds the door boot in place in a front-loading washer. If your washer is leaking from the door and there are no signs of damage to the door boot seal, check to ensure that it is securely fastened. If your boot seal clamp is faulty, or damaged, it should be replaced immediately.

Pump filter (bag)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Hose assembly,drain (drain hose)

Cap,drain hose (hose cap)

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

Clamp

The hose clamp works in conjunction with the water hose in the appliance by holding the water hose in place to keep the hose from leaking water on to the floor. If you notice your appliance leaking, you may have a crack in the hose or that the clamp is loose and will need to be replaced. The hose clamp is made of metal, measures approximately 1/2” in diameter and sold individually. This is a genuine OEM part.

Pump casing (casing)

This part connects to the drain pump and motor.